BugLink: https://bugs.launchpad.net/bugs/2080908
During the boot, kernel get crashed and this is due to
some changes done for RT patches
printk: nbcon: Implement processing in port->lock wrapper
serial: amba-pl011: Use uart_prepare_sysrq_char()
Instead of full revert of above patches, updating the
drivers/tty/serial/amba-pl011.c to get the kernel crash fix.
This is quick fix and proper fix needs to be implement after
finding the rootcause.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Noah Wager <noah.wager@canonical.com>
Acked-by: Jacob Martin <jacob.martin@canonical.com>
Signed-off-by: Noah Wager <noah.wager@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/2080908
Hang is seen when UART if UART transfers are closed abruptly.
The issue is seen only when the UART is running in DMA mode with
internal loopback and HW Flow control enabled.
When force termination happens on UART loopback transfers, the RX
stops before TX. This makes TX to wait for CTS to toggle, which never
happens. This renders UART as busy and makes the driver to wait
endlessly before terminating the DMA transfers.
To fix this, disable HW flow control during the UART shutdown if
loopback is used.
http://nvbugs/3684799http://nvbugs/4754882
Signed-off-by: Kartik <kkartik@nvidia.com>
Tested-by: Petlozu Pravareshwar <petlozup@nvidia.com>
Reviewed-by: Petlozu Pravareshwar <petlozup@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Noah Wager <noah.wager@canonical.com>
Acked-by: Jacob Martin <jacob.martin@canonical.com>
Signed-off-by: Noah Wager <noah.wager@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/2060704
Implement the necessary callbacks to switch the 8250 console driver
to perform as an nbcon console.
Add implementations for the nbcon console callbacks (write_atomic,
write_thread, device_lock, device_unlock), provide @nbcon_drvdata, and
add CON_NBCON to the initial flags.
The legacy code is kept in order to easily switch back to legacy mode
by defining CONFIG_SERIAL_8250_LEGACY_CONSOLE.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
[kevinbecker: context adjustment due to baf4c8f5]
Signed-off-by: Kevin Becker <kevin.becker@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/2060704
Currently the port->lock wrappers uart_port_lock(),
uart_port_unlock() (and their variants) only lock/unlock
the spin_lock.
If the port is an nbcon console, the wrappers must also
acquire/release the console and mark the region as unsafe. This
allows general port->lock synchronization to be synchronized
with the nbcon console ownership.
Introduce a new struct nbcon_drvdata within struct console that
provides the necessary components for the port lock wrappers to
acquire the nbcon console and track its ownership.
Also introduce uart_port_set_cons() as a wrapper to set @cons
of a uart_port. The wrapper sets @cons under the port lock in
order to prevent @cons from disappearing while another context
owns the port lock via the port lock wrappers.
Also cleanup the description of the console_srcu_read_flags()
function. It is used by the port lock wrappers to ensure a
console cannot be fully unregistered while another context
owns the port lock via the port lock wrappers.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kevin Becker <kevin.becker@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/2060704
The struct eg20t_port has a spinlock_t which is used for locking while
access I/O of the device. Then there is the uart_portlock which is
sometimes and nests within eg20t_port's lock.
The uart_port lock is not used while using the struct in
pch_uart_hal_read() which might be okay. Then both locks are used in
pch_console_write() which looks odd especially the double try_lock part.
All in all it looks like the uart_port's lock could replace eg20t_port's
lock and simplify the code.
Remove eg20t_port::lock and use uart_port's lock for the lock scope.
Link: https://lore.kernel.org/r/20240301215246.891055-18-bigeasy@linutronix.de
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kevin Becker <kevin.becker@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/2114239
commit b06f388994500297bb91be60ffaf6825ecfd2afe upstream.
lockdep detects the following circular locking dependency:
CPU 0 CPU 1
========================== ============================
cdns_uart_isr() printk()
uart_port_lock(port) console_lock()
cdns_uart_console_write()
if (!port->sysrq)
uart_port_lock(port)
uart_handle_break()
port->sysrq = ...
uart_handle_sysrq_char()
printk()
console_lock()
The fixed commit attempts to avoid this situation by only taking the
port lock in cdns_uart_console_write if port->sysrq unset. However, if
(as shown above) cdns_uart_console_write runs before port->sysrq is set,
then it will try to take the port lock anyway. This may result in a
deadlock.
Fix this by splitting sysrq handling into two parts. We use the prepare
helper under the port lock and defer handling until we release the lock.
Fixes: 74ea66d4ca ("tty: xuartps: Improve sysrq handling")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Cc: stable@vger.kernel.org # c980248179: serial: xilinx_uartps: Use port lock wrappers
Acked-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20250110213822.2107462-1-sean.anderson@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Noah Wager <noah.wager@canonical.com>
Signed-off-by: Mehmet Basaran <mehmet.basaran@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/2111953
[ Upstream commit d91f98be26510f5f81ec66425bb0306d1ccd571a ]
After a console has written a record into UART_TX, it uses
wait_for_xmitr() to wait until the data has been sent out before
returning. However, wait_for_xmitr() will timeout after 10ms,
regardless if the data has been transmitted or not.
For single bytes, this timeout is sufficient even at very slow
baud rates, such as 1200bps. However, when FIFO mode is used,
there may be 64 bytes pushed into the FIFO at once. At a baud
rate of 115200bps, the 10ms timeout is still sufficient. But
when using lower baud rates (such as 57600bps), the timeout
is _not_ sufficient. This causes longer lines to be cut off,
resulting in lost and horribly misformatted output on the
console.
When using FIFO mode, take the number of bytes into account to
determine an appropriate maximum timeout. Increasing the timeout
does not affect performance since ideally the timeout never
occurs.
Fixes: 8f3631f0f6 ("serial/8250: Use fifo in 8250 console driver")
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Wander Lairson Costa <wander@redhat.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20250107212702.169493-2-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Manuel Diewald <manuel.diewald@canonical.com>
Signed-off-by: Mehmet Basaran <mehmet.basaran@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/2102181
commit 7cc0e0a43a91052477c2921f924a37d9c3891f0c upstream.
On the Renesas RZ/G3S, when doing suspend to RAM, the uart_suspend_port()
is called. The uart_suspend_port() calls 3 times the
struct uart_port::ops::tx_empty() before shutting down the port.
According to the documentation, the struct uart_port::ops::tx_empty()
API tests whether the transmitter FIFO and shifter for the port is
empty.
The Renesas RZ/G3S SCIFA IP reports the number of data units stored in the
transmit FIFO through the FDR (FIFO Data Count Register). The data units
in the FIFOs are written in the shift register and transmitted from there.
The TEND bit in the Serial Status Register reports if the data was
transmitted from the shift register.
In the previous code, in the tx_empty() API implemented by the sh-sci
driver, it is considered that the TX is empty if the hardware reports the
TEND bit set and the number of data units in the FIFO is zero.
According to the HW manual, the TEND bit has the following meaning:
0: Transmission is in the waiting state or in progress.
1: Transmission is completed.
It has been noticed that when opening the serial device w/o using it and
then switch to a power saving mode, the tx_empty() call in the
uart_port_suspend() function fails, leading to the "Unable to drain
transmitter" message being printed on the console. This is because the
TEND=0 if nothing has been transmitted and the FIFOs are empty. As the
TEND=0 has double meaning (waiting state, in progress) we can't
determined the scenario described above.
Add a software workaround for this. This sets a variable if any data has
been sent on the serial console (when using PIO) or if the DMA callback has
been called (meaning something has been transmitted). In the tx_empty()
API the status of the DMA transaction is also checked and if it is
completed or in progress the code falls back in checking the hardware
registers instead of relying on the software variable.
Fixes: 73a19e4c03 ("serial: sh-sci: Add DMA support.")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20241125115856.513642-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[koichiroden: adjusted context due to missing commits:
1788cf6a91d9 ("tty: serial: switch from circ_buf to kfifo")
6deab51402b1 ("serial: sh-sci: Call sci_serial_{in,out}() directly")]
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Signed-off-by: Mehmet Basaran <mehmet.basaran@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/2101915
commit b5a23a60e8ab5711f4952912424347bf3864ce8d upstream.
When CONFIG_DMA_ENGINE is disabled, the driver now fails to build:
drivers/tty/serial/amba-pl011.c: In function 'pl011_unthrottle_rx':
drivers/tty/serial/amba-pl011.c:1822:16: error: 'struct uart_amba_port' has no member named 'using_rx_dma'
1822 | if (uap->using_rx_dma) {
| ^~
drivers/tty/serial/amba-pl011.c:1823:20: error: 'struct uart_amba_port' has no member named 'dmacr'
1823 | uap->dmacr |= UART011_RXDMAE;
| ^~
drivers/tty/serial/amba-pl011.c:1824:32: error: 'struct uart_amba_port' has no member named 'dmacr'
1824 | pl011_write(uap->dmacr, uap, REG_DMACR);
| ^~
Add the missing #ifdef check around these field accesses, matching
what other parts of this driver do.
Fixes: 2bcacc1c87ac ("serial: amba-pl011: Fix RX stall when DMA is used")
Cc: stable <stable@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202411140617.nkjeHhsK-lkp@intel.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20241115110021.744332-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/2101915
commit bcc7ba668818dcadd2f1db66b39ed860a63ecf97 upstream.
Currently in omap_8250_shutdown, the dma->rx_running flag is
set to zero in omap_8250_rx_dma_flush. Next pm_runtime_get_sync
is called, which is a runtime resume call stack which can
re-set the flag. When the call omap_8250_shutdown returns, the
flag is expected to be UN-SET, but this is not the case. This
is causing issues the next time UART is re-opened and
omap_8250_rx_dma is called. Fix by moving pm_runtime_get_sync
before the omap_8250_rx_dma_flush.
cc: stable@vger.kernel.org
Fixes: 0e31c8d173 ("tty: serial: 8250_omap: add custom DMA-RX callback")
Signed-off-by: Bin Liu <b-liu@ti.com>
[Judith: Add commit message]
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20241031172315.453750-1-jm@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/2097393
commit fa103d2599e11e802c818684cff821baefe7f206 upstream.
The receiver is supposed to be enabled in the startup() callback and not
in set_termios() which is called also during console setup.
This specifically avoids accepting input before the port has been opened
(and interrupts enabled), something which can also break the GENI
firmware (cancel fails and after abort, the "stale" counter handling
appears to be broken so that later input is not processed until twelve
chars have been received).
There also does not appear to be any need to keep the receiver disabled
while updating the port settings.
Since commit 6f3c3cafb115 ("serial: qcom-geni: disable interrupts during
console writes") the calls to manipulate the secondary interrupts, which
were done without holding the port lock, can also lead to the receiver
being left disabled when set_termios() races with the console code (e.g.
when init opens the tty during boot). This can manifest itself as a
serial getty not accepting input.
The calls to stop and start rx in set_termios() can similarly race with
DMA completion and, for example, cause the DMA buffer to be unmapped
twice or the mapping to be leaked.
Fix this by only enabling the receiver during startup and while holding
the port lock to avoid racing with the console code.
Fixes: 6f3c3cafb115 ("serial: qcom-geni: disable interrupts during console writes")
Fixes: 2aaa43c707 ("tty: serial: qcom-geni-serial: add support for serial engine DMA")
Fixes: c4f528795d ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Cc: stable@vger.kernel.org # 6.3
Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20241009145110.16847-6-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Manuel Diewald <manuel.diewald@canonical.com>
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/2097393
commit 23ee4a25661c33e6381d41e848a9060ed6d72845 upstream.
Make sure to wait for the DMA transfer to complete when cancelling the
rx command on stop_rx(). This specifically prevents the DMA completion
interrupt from firing after rx has been restarted, something which can
lead to an IOMMU fault and hosed rx when the interrupt handler unmaps
the DMA buffer for the new command:
qcom_geni_serial 988000.serial: serial engine reports 0 RX bytes in!
arm-smmu 15000000.iommu: FSR = 00000402 [Format=2 TF], SID=0x563
arm-smmu 15000000.iommu: FSYNR0 = 00210013 [S1CBNDX=33 WNR PLVL=3]
Bluetooth: hci0: command 0xfc00 tx timeout
Bluetooth: hci0: Reading QCA version information failed (-110)
Also add the missing state machine reset which is needed in case
cancellation fails.
Fixes: 2aaa43c707 ("tty: serial: qcom-geni-serial: add support for serial engine DMA")
Cc: stable@vger.kernel.org # 6.3
Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241009145110.16847-5-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Manuel Diewald <manuel.diewald@canonical.com>
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/2097393
commit 19df76662a33d2f2fc41a66607cb8285fc02d6ec upstream.
This reverts commit 35781d8356.
Hibernation is not supported on Qualcomm platforms with mainline
kernels yet a broken vendor implementation for the GENI serial driver
made it upstream.
This is effectively dead code that cannot be tested and should just be
removed, but if these paths were ever hit for an open non-console port
they would crash the machine as the driver would fail to enable clocks
during restore() (i.e. all ports would have to be closed by drivers and
user space before hibernating the system to avoid this as a comment in
the code hinted at).
The broken implementation also added a random call to enable the
receiver in the port setup code where it does not belong and which
enables the receiver prematurely for console ports.
Fixes: 35781d8356 ("tty: serial: qcom-geni-serial: Add support for Hibernation feature")
Cc: stable@vger.kernel.org # 6.2
Cc: Aniket Randive <quic_arandive@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241009145110.16847-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Manuel Diewald <manuel.diewald@canonical.com>
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/2097393
commit 40d7903386df4d18f04d90510ba90eedee260085 upstream.
When sending data using DMA at high baudrate (4 Mbdps in local test case) to
a device with small RX buffer which keeps asserting RTS after every received
byte, it is possible that the iMX UART driver would not recognize the falling
edge of RTS input signal and get stuck, unable to transmit any more data.
This condition happens when the following sequence of events occur:
- imx_uart_mctrl_check() is called at some point and takes a snapshot of UART
control signal status into sport->old_status using imx_uart_get_hwmctrl().
The RTSS/TIOCM_CTS bit is of interest here (*).
- DMA transfer occurs, the remote device asserts RTS signal after each byte.
The i.MX UART driver recognizes each such RTS signal change, raises an
interrupt with USR1 register RTSD bit set, which leads to invocation of
__imx_uart_rtsint(), which calls uart_handle_cts_change().
- If the RTS signal is deasserted, uart_handle_cts_change() clears
port->hw_stopped and unblocks the port for further data transfers.
- If the RTS is asserted, uart_handle_cts_change() sets port->hw_stopped
and blocks the port for further data transfers. This may occur as the
last interrupt of a transfer, which means port->hw_stopped remains set
and the port remains blocked (**).
- Any further data transfer attempts will trigger imx_uart_mctrl_check(),
which will read current status of UART control signals by calling
imx_uart_get_hwmctrl() (***) and compare it with sport->old_status .
- If current status differs from sport->old_status for RTS signal,
uart_handle_cts_change() is called and possibly unblocks the port
by clearing port->hw_stopped .
- If current status does not differ from sport->old_status for RTS
signal, no action occurs. This may occur in case prior snapshot (*)
was taken before any transfer so the RTS is deasserted, current
snapshot (***) was taken after a transfer and therefore RTS is
deasserted again, which means current status and sport->old_status
are identical. In case (**) triggered when RTS got asserted, and
made port->hw_stopped set, the port->hw_stopped will remain set
because no change on RTS line is recognized by this driver and
uart_handle_cts_change() is not called from here to unblock the
port->hw_stopped.
Update sport->old_status in __imx_uart_rtsint() accordingly to make
imx_uart_mctrl_check() detect such RTS change. Note that TIOCM_CAR
and TIOCM_RI bits in sport->old_status do not suffer from this problem.
Fixes: ceca629e0b ("[ARM] 2971/1: i.MX uart handle rts irq")
Cc: stable <stable@kernel.org>
Reviewed-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20241002184133.19427-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Manuel Diewald <manuel.diewald@canonical.com>
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/2097301
[ Upstream commit 602babaa84d627923713acaf5f7e9a4369e77473 ]
Commit af224ca2df (serial: core: Prevent unsafe uart port access, part
3) added few uport == NULL checks. It added one to uart_shutdown(), so
the commit assumes, uport can be NULL in there. But right after that
protection, there is an unprotected "uart_port_dtr_rts(uport, false);"
call. That is invoked only if HUPCL is set, so I assume that is the
reason why we do not see lots of these reports.
Or it cannot be NULL at this point at all for some reason :P.
Until the above is investigated, stay on the safe side and move this
dereference to the if too.
I got this inconsistency from Coverity under CID 1585130. Thanks.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240805102046.307511-3-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
CVE-2024-50058
Signed-off-by: Manuel Diewald <manuel.diewald@canonical.com>
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Kartik Rajput
Laxman Dewangan
John Ogness
Sebastian Andrzej Siewior
Claudiu Beznea
Sean Anderson
Ben Wolsieffer
Ilpo Järvinen
Inochi Amaoto
Arnd Bergmann
Bin Liu
Filip Brozovic
Johan Hovold
Marek Vasut
Jiri Slaby (SUSE)
Douglas Anderson