BugLink: https://bugs.launchpad.net/bugs/2080908
During the boot, kernel get crashed and this is due to
some changes done for RT patches
printk: nbcon: Implement processing in port->lock wrapper
serial: amba-pl011: Use uart_prepare_sysrq_char()
Instead of full revert of above patches, updating the
drivers/tty/serial/amba-pl011.c to get the kernel crash fix.
This is quick fix and proper fix needs to be implement after
finding the rootcause.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Noah Wager <noah.wager@canonical.com>
Acked-by: Jacob Martin <jacob.martin@canonical.com>
Signed-off-by: Noah Wager <noah.wager@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/2080908
Hang is seen when UART if UART transfers are closed abruptly.
The issue is seen only when the UART is running in DMA mode with
internal loopback and HW Flow control enabled.
When force termination happens on UART loopback transfers, the RX
stops before TX. This makes TX to wait for CTS to toggle, which never
happens. This renders UART as busy and makes the driver to wait
endlessly before terminating the DMA transfers.
To fix this, disable HW flow control during the UART shutdown if
loopback is used.
http://nvbugs/3684799http://nvbugs/4754882
Signed-off-by: Kartik <kkartik@nvidia.com>
Tested-by: Petlozu Pravareshwar <petlozup@nvidia.com>
Reviewed-by: Petlozu Pravareshwar <petlozup@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Noah Wager <noah.wager@canonical.com>
Acked-by: Jacob Martin <jacob.martin@canonical.com>
Signed-off-by: Noah Wager <noah.wager@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/2060704
Implement the necessary callbacks to switch the 8250 console driver
to perform as an nbcon console.
Add implementations for the nbcon console callbacks (write_atomic,
write_thread, device_lock, device_unlock), provide @nbcon_drvdata, and
add CON_NBCON to the initial flags.
The legacy code is kept in order to easily switch back to legacy mode
by defining CONFIG_SERIAL_8250_LEGACY_CONSOLE.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
[kevinbecker: context adjustment due to baf4c8f5]
Signed-off-by: Kevin Becker <kevin.becker@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/2060704
Currently the port->lock wrappers uart_port_lock(),
uart_port_unlock() (and their variants) only lock/unlock
the spin_lock.
If the port is an nbcon console, the wrappers must also
acquire/release the console and mark the region as unsafe. This
allows general port->lock synchronization to be synchronized
with the nbcon console ownership.
Introduce a new struct nbcon_drvdata within struct console that
provides the necessary components for the port lock wrappers to
acquire the nbcon console and track its ownership.
Also introduce uart_port_set_cons() as a wrapper to set @cons
of a uart_port. The wrapper sets @cons under the port lock in
order to prevent @cons from disappearing while another context
owns the port lock via the port lock wrappers.
Also cleanup the description of the console_srcu_read_flags()
function. It is used by the port lock wrappers to ensure a
console cannot be fully unregistered while another context
owns the port lock via the port lock wrappers.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kevin Becker <kevin.becker@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/2060704
The struct eg20t_port has a spinlock_t which is used for locking while
access I/O of the device. Then there is the uart_portlock which is
sometimes and nests within eg20t_port's lock.
The uart_port lock is not used while using the struct in
pch_uart_hal_read() which might be okay. Then both locks are used in
pch_console_write() which looks odd especially the double try_lock part.
All in all it looks like the uart_port's lock could replace eg20t_port's
lock and simplify the code.
Remove eg20t_port::lock and use uart_port's lock for the lock scope.
Link: https://lore.kernel.org/r/20240301215246.891055-18-bigeasy@linutronix.de
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kevin Becker <kevin.becker@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/2114239
commit ee6a44da3c87cf64d67dd02be8c0127a5bf56175 upstream.
This requirement was overeagerly loosened in commit 2f83e38a095f
("tty: Permit some TIOCL_SETSEL modes without CAP_SYS_ADMIN"), but as
it turns out,
(1) the logic I implemented there was inconsistent (apologies!),
(2) TIOCL_SELMOUSEREPORT might actually be a small security risk
after all, and
(3) TIOCL_SELMOUSEREPORT is only meant to be used by the mouse
daemon (GPM or Consolation), which runs as CAP_SYS_ADMIN
already.
In more detail:
1. The previous patch has inconsistent logic:
In commit 2f83e38a095f ("tty: Permit some TIOCL_SETSEL modes
without CAP_SYS_ADMIN"), we checked for sel_mode ==
TIOCL_SELMOUSEREPORT, but overlooked that the lower four bits of
this "mode" parameter were actually used as an additional way to
pass an argument. So the patch did actually still require
CAP_SYS_ADMIN, if any of the mouse button bits are set, but did not
require it if none of the mouse buttons bits are set.
This logic is inconsistent and was not intentional. We should have
the same policies for using TIOCL_SELMOUSEREPORT independent of the
value of the "hidden" mouse button argument.
I sent a separate documentation patch to the man page list with
more details on TIOCL_SELMOUSEREPORT:
https://lore.kernel.org/all/20250223091342.35523-2-gnoack3000@gmail.com/
2. TIOCL_SELMOUSEREPORT is indeed a potential security risk which can
let an attacker simulate "keyboard" input to command line
applications on the same terminal, like TIOCSTI and some other
TIOCLINUX "selection mode" IOCTLs.
By enabling mouse reporting on a terminal and then injecting mouse
reports through TIOCL_SELMOUSEREPORT, an attacker can simulate
mouse movements on the same terminal, similar to the TIOCSTI
keystroke injection attacks that were previously possible with
TIOCSTI and other TIOCL_SETSEL selection modes.
Many programs (including libreadline/bash) are then prone to
misinterpret these mouse reports as normal keyboard input because
they do not expect input in the X11 mouse protocol form. The
attacker does not have complete control over the escape sequence,
but they can at least control the values of two consecutive bytes
in the binary mouse reporting escape sequence.
I went into more detail on that in the discussion at
https://lore.kernel.org/all/20250221.0a947528d8f3@gnoack.org/
It is not equally trivial to simulate arbitrary keystrokes as it
was with TIOCSTI (commit 83efeeeb3d ("tty: Allow TIOCSTI to be
disabled")), but the general mechanism is there, and together with
the small number of existing legit use cases (see below), it would
be better to revert back to requiring CAP_SYS_ADMIN for
TIOCL_SELMOUSEREPORT, as it was already the case before
commit 2f83e38a095f ("tty: Permit some TIOCL_SETSEL modes without
CAP_SYS_ADMIN").
3. TIOCL_SELMOUSEREPORT is only used by the mouse daemons (GPM or
Consolation), and they are the only legit use case:
To quote console_codes(4):
The mouse tracking facility is intended to return
xterm(1)-compatible mouse status reports. Because the console
driver has no way to know the device or type of the mouse, these
reports are returned in the console input stream only when the
virtual terminal driver receives a mouse update ioctl. These
ioctls must be generated by a mouse-aware user-mode application
such as the gpm(8) daemon.
Jared Finder has also confirmed in
https://lore.kernel.org/all/491f3df9de6593df8e70dbe77614b026@finder.org/
that Emacs does not call TIOCL_SELMOUSEREPORT directly, and it
would be difficult to find good reasons for doing that, given that
it would interfere with the reports that GPM is sending.
More information on the interaction between GPM, terminals and the
kernel with additional pointers is also available in this patch:
https://lore.kernel.org/all/a773e48920aa104a65073671effbdee665c105fc.1603963593.git.tammo.block@gmail.com/
For background on who else uses TIOCL_SELMOUSEREPORT: Debian Code
search finds one page of results, the only two known callers are
the two mouse daemons GPM and Consolation. (GPM does not show up
in the search results because it uses literal numbers to refer to
TIOCLINUX-related enums. I looked through GPM by hand instead.
TIOCL_SELMOUSEREPORT is also not used from libgpm.)
https://codesearch.debian.net/search?q=TIOCL_SELMOUSEREPORT
Cc: Jared Finder <jared@finder.org>
Cc: Jann Horn <jannh@google.com>
Cc: Hanno Böck <hanno@hboeck.de>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Kees Cook <kees@kernel.org>
Cc: stable <stable@kernel.org>
Fixes: 2f83e38a095f ("tty: Permit some TIOCL_SETSEL modes without CAP_SYS_ADMIN")
Signed-off-by: Günther Noack <gnoack3000@gmail.com>
Link: https://lore.kernel.org/r/20250411070144.3959-2-gnoack3000@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 6f021bc0083b96125fdbed6a60d7b4396c4d6dac linux-6.12.y)
[nwager: Follow-up fix from 6.12.26]
Signed-off-by: Noah Wager <noah.wager@canonical.com>
Signed-off-by: Mehmet Basaran <mehmet.basaran@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/2114239
Pass proper types and proper pointers (the data with an offset) to the
TIOCL_* handlers. So that they need not to cast or add anything to the
passed pointer.
This makes obvious what is passed/consumed.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Tested-by: Helge Deller <deller@gmx.de> # parisc STI console
Link: https://lore.kernel.org/r/20240122110401.7289-6-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit a0b8a1681254346010edd2f94e799fb6b6568cf1)
[nwager: This is just a cleanup commit that doesn't change behaviour and
makes the following 6.12.14 patch apply cleanly:
e46d91ca504d ("tty: Permit some TIOCL_SETSEL modes without CAP_SYS_ADMIN")]
Signed-off-by: Noah Wager <noah.wager@canonical.com>
Signed-off-by: Mehmet Basaran <mehmet.basaran@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/2114239
commit b06f388994500297bb91be60ffaf6825ecfd2afe upstream.
lockdep detects the following circular locking dependency:
CPU 0 CPU 1
========================== ============================
cdns_uart_isr() printk()
uart_port_lock(port) console_lock()
cdns_uart_console_write()
if (!port->sysrq)
uart_port_lock(port)
uart_handle_break()
port->sysrq = ...
uart_handle_sysrq_char()
printk()
console_lock()
The fixed commit attempts to avoid this situation by only taking the
port lock in cdns_uart_console_write if port->sysrq unset. However, if
(as shown above) cdns_uart_console_write runs before port->sysrq is set,
then it will try to take the port lock anyway. This may result in a
deadlock.
Fix this by splitting sysrq handling into two parts. We use the prepare
helper under the port lock and defer handling until we release the lock.
Fixes: 74ea66d4ca ("tty: xuartps: Improve sysrq handling")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Cc: stable@vger.kernel.org # c980248179: serial: xilinx_uartps: Use port lock wrappers
Acked-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20250110213822.2107462-1-sean.anderson@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Noah Wager <noah.wager@canonical.com>
Signed-off-by: Mehmet Basaran <mehmet.basaran@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/2111953
[ Upstream commit d91f98be26510f5f81ec66425bb0306d1ccd571a ]
After a console has written a record into UART_TX, it uses
wait_for_xmitr() to wait until the data has been sent out before
returning. However, wait_for_xmitr() will timeout after 10ms,
regardless if the data has been transmitted or not.
For single bytes, this timeout is sufficient even at very slow
baud rates, such as 1200bps. However, when FIFO mode is used,
there may be 64 bytes pushed into the FIFO at once. At a baud
rate of 115200bps, the 10ms timeout is still sufficient. But
when using lower baud rates (such as 57600bps), the timeout
is _not_ sufficient. This causes longer lines to be cut off,
resulting in lost and horribly misformatted output on the
console.
When using FIFO mode, take the number of bytes into account to
determine an appropriate maximum timeout. Increasing the timeout
does not affect performance since ideally the timeout never
occurs.
Fixes: 8f3631f0f6 ("serial/8250: Use fifo in 8250 console driver")
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Wander Lairson Costa <wander@redhat.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20250107212702.169493-2-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Manuel Diewald <manuel.diewald@canonical.com>
Signed-off-by: Mehmet Basaran <mehmet.basaran@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/2111953
[ Upstream commit 9722c3b66e21ff08aec570d02a97d331087fd70f ]
The of_property_for_each_u32() macro needs five parameters, two of which
are primarily meant as internal variables for the macro itself (in the
for() clause). Yet these two parameters are used by a few drivers, and this
can be considered misuse or at least bad practice.
Now that the kernel uses C11 to build, these two parameters can be avoided
by declaring them internally, thus changing this pattern:
struct property *prop;
const __be32 *p;
u32 val;
of_property_for_each_u32(np, "xyz", prop, p, val) { ... }
to this:
u32 val;
of_property_for_each_u32(np, "xyz", val) { ... }
However two variables cannot be declared in the for clause even with C11,
so declare one struct that contain the two variables we actually need. As
the variables inside this struct are not meant to be used by users of this
macro, give the struct instance the noticeable name "_it" so it is visible
during code reviews, helping to avoid new code to use it directly.
Most usages are trivially converted as they do not use those two
parameters, as expected. The non-trivial cases are:
- drivers/clk/clk.c, of_clk_get_parent_name(): easily doable anyway
- drivers/clk/clk-si5351.c, si5351_dt_parse(): this is more complex as the
checks had to be replicated in a different way, making code more verbose
and somewhat uglier, but I refrained from a full rework to keep as much
of the original code untouched having no hardware to test my changes
All the changes have been build tested. The few for which I have the
hardware have been runtime-tested too.
Reviewed-by: Andre Przywara <andre.przywara@arm.com> # drivers/clk/sunxi/clk-simple-gates.c, drivers/clk/sunxi/clk-sun8i-bus-gates.c
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> # drivers/gpio/gpio-brcmstb.c
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> # drivers/irqchip/irq-atmel-aic-common.c
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # drivers/iio/adc/ti_am335x_adc.c
Acked-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com> # drivers/pwm/pwm-samsung.c
Acked-by: Richard Leitner <richard.leitner@linux.dev> # drivers/usb/misc/usb251xb.c
Acked-by: Mark Brown <broonie@kernel.org> # sound/soc/codecs/arizona.c
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com> # sound/soc/codecs/arizona.c
Acked-by: Michael Ellerman <mpe@ellerman.id.au> # arch/powerpc/sysdev/xive/spapr.c
Acked-by: Stephen Boyd <sboyd@kernel.org> # clk
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Acked-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20240724-of_property_for_each_u32-v3-1-bea82ce429e2@bootlin.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Stable-dep-of: 28fa3291cad1 ("clk: fix an OF node reference leak in of_clk_get_parent_name()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Manuel Diewald <manuel.diewald@canonical.com>
Signed-off-by: Mehmet Basaran <mehmet.basaran@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/2102181
commit 7cc0e0a43a91052477c2921f924a37d9c3891f0c upstream.
On the Renesas RZ/G3S, when doing suspend to RAM, the uart_suspend_port()
is called. The uart_suspend_port() calls 3 times the
struct uart_port::ops::tx_empty() before shutting down the port.
According to the documentation, the struct uart_port::ops::tx_empty()
API tests whether the transmitter FIFO and shifter for the port is
empty.
The Renesas RZ/G3S SCIFA IP reports the number of data units stored in the
transmit FIFO through the FDR (FIFO Data Count Register). The data units
in the FIFOs are written in the shift register and transmitted from there.
The TEND bit in the Serial Status Register reports if the data was
transmitted from the shift register.
In the previous code, in the tx_empty() API implemented by the sh-sci
driver, it is considered that the TX is empty if the hardware reports the
TEND bit set and the number of data units in the FIFO is zero.
According to the HW manual, the TEND bit has the following meaning:
0: Transmission is in the waiting state or in progress.
1: Transmission is completed.
It has been noticed that when opening the serial device w/o using it and
then switch to a power saving mode, the tx_empty() call in the
uart_port_suspend() function fails, leading to the "Unable to drain
transmitter" message being printed on the console. This is because the
TEND=0 if nothing has been transmitted and the FIFOs are empty. As the
TEND=0 has double meaning (waiting state, in progress) we can't
determined the scenario described above.
Add a software workaround for this. This sets a variable if any data has
been sent on the serial console (when using PIO) or if the DMA callback has
been called (meaning something has been transmitted). In the tx_empty()
API the status of the DMA transaction is also checked and if it is
completed or in progress the code falls back in checking the hardware
registers instead of relying on the software variable.
Fixes: 73a19e4c03 ("serial: sh-sci: Add DMA support.")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20241125115856.513642-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[koichiroden: adjusted context due to missing commits:
1788cf6a91d9 ("tty: serial: switch from circ_buf to kfifo")
6deab51402b1 ("serial: sh-sci: Call sci_serial_{in,out}() directly")]
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Signed-off-by: Mehmet Basaran <mehmet.basaran@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/2101915
commit b5a23a60e8ab5711f4952912424347bf3864ce8d upstream.
When CONFIG_DMA_ENGINE is disabled, the driver now fails to build:
drivers/tty/serial/amba-pl011.c: In function 'pl011_unthrottle_rx':
drivers/tty/serial/amba-pl011.c:1822:16: error: 'struct uart_amba_port' has no member named 'using_rx_dma'
1822 | if (uap->using_rx_dma) {
| ^~
drivers/tty/serial/amba-pl011.c:1823:20: error: 'struct uart_amba_port' has no member named 'dmacr'
1823 | uap->dmacr |= UART011_RXDMAE;
| ^~
drivers/tty/serial/amba-pl011.c:1824:32: error: 'struct uart_amba_port' has no member named 'dmacr'
1824 | pl011_write(uap->dmacr, uap, REG_DMACR);
| ^~
Add the missing #ifdef check around these field accesses, matching
what other parts of this driver do.
Fixes: 2bcacc1c87ac ("serial: amba-pl011: Fix RX stall when DMA is used")
Cc: stable <stable@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202411140617.nkjeHhsK-lkp@intel.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20241115110021.744332-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/2101915
commit bcc7ba668818dcadd2f1db66b39ed860a63ecf97 upstream.
Currently in omap_8250_shutdown, the dma->rx_running flag is
set to zero in omap_8250_rx_dma_flush. Next pm_runtime_get_sync
is called, which is a runtime resume call stack which can
re-set the flag. When the call omap_8250_shutdown returns, the
flag is expected to be UN-SET, but this is not the case. This
is causing issues the next time UART is re-opened and
omap_8250_rx_dma is called. Fix by moving pm_runtime_get_sync
before the omap_8250_rx_dma_flush.
cc: stable@vger.kernel.org
Fixes: 0e31c8d173 ("tty: serial: 8250_omap: add custom DMA-RX callback")
Signed-off-by: Bin Liu <b-liu@ti.com>
[Judith: Add commit message]
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20241031172315.453750-1-jm@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/2097393
commit fa103d2599e11e802c818684cff821baefe7f206 upstream.
The receiver is supposed to be enabled in the startup() callback and not
in set_termios() which is called also during console setup.
This specifically avoids accepting input before the port has been opened
(and interrupts enabled), something which can also break the GENI
firmware (cancel fails and after abort, the "stale" counter handling
appears to be broken so that later input is not processed until twelve
chars have been received).
There also does not appear to be any need to keep the receiver disabled
while updating the port settings.
Since commit 6f3c3cafb115 ("serial: qcom-geni: disable interrupts during
console writes") the calls to manipulate the secondary interrupts, which
were done without holding the port lock, can also lead to the receiver
being left disabled when set_termios() races with the console code (e.g.
when init opens the tty during boot). This can manifest itself as a
serial getty not accepting input.
The calls to stop and start rx in set_termios() can similarly race with
DMA completion and, for example, cause the DMA buffer to be unmapped
twice or the mapping to be leaked.
Fix this by only enabling the receiver during startup and while holding
the port lock to avoid racing with the console code.
Fixes: 6f3c3cafb115 ("serial: qcom-geni: disable interrupts during console writes")
Fixes: 2aaa43c707 ("tty: serial: qcom-geni-serial: add support for serial engine DMA")
Fixes: c4f528795d ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Cc: stable@vger.kernel.org # 6.3
Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20241009145110.16847-6-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Manuel Diewald <manuel.diewald@canonical.com>
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Kartik Rajput
Laxman Dewangan
John Ogness
Sebastian Andrzej Siewior
Claudiu Beznea
Günther Noack
Günther Noack
Jiri Slaby (SUSE)
Sean Anderson
Luca Ceresoli
Ben Wolsieffer
Ilpo Järvinen
Inochi Amaoto
Arnd Bergmann
Bin Liu
Filip Brozovic
Nicolas Bouchinet
Johan Hovold