Register interconnect links between IP blocks, rather than the IP
blocks themselves. (The IP blocks will be registered as a side-effect
of registering the links.)
The objective is to reduce the number of lines of static data and
facilitate the sharing of IP block data between different SoCs. These
objectives come at the penalty of increased boot time due to increased
computation.
While here, fix a few whitespace problems and inaccurate variable names.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Add support for direct IP block interconnect ("link") registration to
the hwmod code via a new function, omap_hwmod_register_links(). This
will replace direct registration of hwmods, and a subsequent patch
will remove omap_hwmod_register().
This change will allow a subsequent patch to remove the hwmod data
link arrays. This will reduce the size of the hwmod static data and
also make it easier to generate the data files. It will also make it
possible to share some of the struct omap_hwmod records across
multiple SoCs, since the link array pointers will be removed from the
struct omap_hwmod.
The downside is that boot time will increase. Minimizing boot time
was the reason why the link arrays were originally introduced.
Removing them will require extra computation during boot to allocate
memory and associate IP blocks with their interconnects. However,
since the current kernel development focus is on reducing the number
of lines in arch/arm/mach-omap2/, boot time impact is now seemingly
considered a lower priority.
This patch contains additional complexity to reduce the number of
memory allocations required for this change. This reduces the boot
time impact: total hwmod link registration time was ~ 2655
microseconds with a simple allocation strategy, but is now ~ 549
microseconds[1] with the approach taken by this patch.
1. Measured on a BeagleBoard 35xx @ 500MHz MPU/333 MHz CORE, average
of 7 samples. Total uncertainty is +/- 61 microseconds.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
An IP block's MPU interface port only needs to be found once. The result
can be cached to speed further lookups. This patch consolidates these
two steps into a single function.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
To reduce the number of lines of data in the OMAP portion of the Linux
code base, subsequent patches will remove the lists of hwmod
interconnect links from the static hwmod data. These lists will be
built dynamically during boot. To ease this transition, this patch
centralizes the way that interconnect links are iterated into a single
function, _fetch_next_ocp_if().
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Most IP blocks on the OMAP SoC have an interconnect link that is
intended to be used by the MPU to communicate with the IP block.
Several parts of the hwmod code need to be able to identify this link.
Currently, this is open-coded. However, future patches will change
the way that interconnect links are represented and will make
identifying the link more complex. So to avoid code duplication, this
patch centralizes the MPU port link identification code into a new
function, _find_mpu_rt_port().
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
While refactoring the mute-LED handling for HP laptops, I messed up
the polarity check in a wrong way. The red (or the mute-LED if any)
should appear in the muted state, corresponding to GPIO on.
Reported-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Extend the OCP_* register offsets in the struct
omap_hwmod_class_sysconfig to 32 bits. This is required to add the
OMAP4+ GPU hwmod, which uses OCP_* register offsets larger than 16
bits.
Another possible solution may be to simply add a single 16 bit offset
field in this structure, and to add code to factor that offset into
all OCP_* register accesses. This would save some memory, since
almost no modules need 32 bit offsets.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Some hwmods were commented out from the OMAP4 data, under the theory
that they shouldn't be added until drivers were ready. But part of
the utility of the hwmod code is that it can reset and properly
initialize IP blocks that have no drivers associated with them.
Rather than commenting the links in the future hwmod data conversion
patches, discussing this with Benoit, it seems best to simply
uncomment them now.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
One of the OMAP4 links was missing OCP_USER flags, since it was only
used by the DSP initiator, and we did not have an OCP_USER_DSP flag.
Future patches will switch the hwmod code and data to register
interfaces, rather than hwmods, and it will be mandatory for all
interfaces to have at least one user bit set. This patch resolves the
issue by adding OCP_USER_DSP and marking the DSP-IVA interface
appropriately.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Commit 407a6888f7 ("OMAP4: hwmod data:
Add AESS, McPDM, bandgap, counter_32k, MMC, KBD, ISS & IPU") adds a
hwmod for the bandgap die temperature sensor IP block. This IP block
has no interconnect port or firewall region, nor does it have an
independent register space or OCP control registers. Its registers
are embedded in the System Control Module (SCM) IP block. So it
appears that the bandgap device should be created by the SCM driver.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
GPTIMER12 is attached to the L4 SEC interconnect, not directly to L4 WKUP.
Add the L4 SEC interconnect and attach GPTIMER12 to it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP3 hwmod data was missing a DSS->L3 interconnect link for the
OMAP3430 ES1 DSS hwmod. Since the hwmod code and data is being modified
to register interfaces rather than hwmods, this would result in the DSS hwmod
not being registered correctly on OMAP3430ES1.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit a52e2ab66d ("ARM: OMAP3: hwmod
data: disable multiblock reads on MMC1/2 on OMAP34xx/35xx <= ES2.1")
didn't link the MMC hwmods to the interconnects correctly. Future
patches will register hwmods by interface, so if this is not fixed,
the MMC IP blocks won't be registered. Update the interface data
records to point to the correct IP blocks.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some of the 2xxx and 3xxx hwmod data files use the old naming style
for hwmods, ending in a "_hwmod". These names are used by the OMAP
integration code to map hwmods to platform_devices, so they need to be
consistent, or the platform_devices won't be created. Remove the
_hwmod suffix to conform with the rest of the OMAP SoC data.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
arch/arm/mach-omap2/timer.c pokes around inside the hwmod data
structures. Since the hwmod data structures are about to change, this
code will break. This patch modifies the timer code to use
recently-added hwmod functions instead.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
The timer integration code pokes around in hwmod data structures.
Those data structures are about to change. Define a function,
omap_hwmod_get_resource_byname(), for the timer integration code to
use instead.
The original patch has been changed to use struct resource by Tony's
request, although the caller of this function should not be a driver._
Platform drivers should get their data through the regular platform_*
functions; DT drivers through the appropriate of_* functions. This a
function is only for use by OMAP core code in arch/arm/*omap*.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
A subsequent patch will need to know the struct omap_hwmod_addr_space
record corresponding to the module's register target, used by the MPU.
So, convert _find_mpu_rt_base() into _find_mpu_rt_addr_space(). Then
modify its sole current user, _populate_mpu_rt_base(), to extract the
MPU RT base address itself from the struct omap_hwmod_addr_space record.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Change the way that hardreset lines are handled by the hwmod code.
Hardreset lines are generally associated with initiator IP blocks.
Prior to this change, the hwmod code expected to control hardreset
lines itself, asserting them on shutdown and deasserting them upon
enable. But driver authors inside TI have commented to us that their
drivers require direct control over these lines. Unfortunately, these
drivers haven't been posted publicly yet, so it's hard to determine
exactly what is needed, a priori. This change attempts to set forth
some reasonable semantics that should be an improvement over the
current code.
The semantics implemented by this patch are as follows:
- If the hwmod is not marked with HWMOD_INIT_NO_RESET, then assert all
associated hardreset lines during IP block setup. This is intended
to place the IP blocks into a known state that will not interfere
with other devices during kernel boot.
- IP blocks with hardreset lines will not be automatically enabled or
idled during setup. Instead, they will be left in the INITIALIZED
state.
- When the hwmod code is asked to enable, idle, or shutdown an IP
block with asserted hardreset lines, the hwmod code will do nothing.
The driver integration code must do the remaining work needed to
control these IP blocks. Once this driver integration code is posted
to the lists, hopefully we can consolidate it and move it inside the
hwmod code.
Custom reset functions for IP blocks with hardreset lines still should
be supported and are strongly endorsed. It is intended that every
subsystem with hardreset lines should have a custom reset function
that can place their subsystem into quiescent idle with the hardreset
lines deasserted.
This reverts most of commit 5365efbe29
("OMAP: hwmod: Add hardreset management support"). Later code
reorganizations caused the sequencing of the code from this patch to
be changed, anyway.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Reorganize the code involved in resetting and configuring an IP block
to make it easier to read and maintain. This involves improving
documentation, splitting some large functions up into smaller ones to
better conform with Documentation/CodingStyle, and removing some
unnecessary code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Most of these have been purged years ago. This one silently lived
on until commit 69349c2dc0
"kconfig: fix IS_ENABLED to not require all options to be defined"
In the above, we use some macro trickery to create a conditional that
is valid in CPP and in C usage. However that trickery doesn't sit
well if you have the legacy "-traditional" flag enabled. You'll get:
AS arch/cris/arch-v10/lib/checksum.o
In file included from <command-line>:4:0:
include/linux/kconfig.h:23:0: error: syntax error in macro parameter list
make[2]: *** [arch/cris/arch-v10/lib/checksum.o] Error 1
Everything builds fine w/o "-traditional" so simply drop it from this
location as well.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
While the trap number and error code are passed around for debugging
purposes, this occurs wholly independently of the thread struct values.
These values were never part of the sigcontext ABI and are thus never
passed anywhere, so we can just kill them off across the board.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Move the sourcing of the board specific Kconfig files into the
"Board support" menu. Without this they appear underneath the
"Board support" menu, in the "System type" menu.
[lethal@linux-sh.org: handle the magicpanelr2 case, too]
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
In some cases the opps error reporting doesn't give enough information
to diagnose the problem, only printing information if it is thought
to be valid. Replace the current code with more detailed output.
This code is based on the ARM reporting, with minor changes for the SH.
[lethal@linux-sh.org: fixed up for 64-bit PTEs and pte_offset_kernel()]
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Reorganize the code involved in initializing the internal data for
each hwmod to make it easier to read and maintain. This involves
improving documentation and removing some duplicated and unnecessary
code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
The problem is caused by the interaction of two features in the Linux
memory management code.
A processes address space is described by a struct mm_struct, and
every thread has a pointer to the mm it should run in. The exception
to this are kernel threads, which don't have an mm, and so borrow
the mm from the last thread which ran. The system is bootstrapped
by the initial kernel thread using init's mm (even though init hasn't
been created yet, its mm is the static init_mm).
The other feature is how the kernel handles the page table which
describes the portion of the address space which is only visible when
executing inside the kernel, and which is shared by all threads. On
the SH4 the only portion of the kernel's address space which described
using the page table is called P3, from 0xc0000000 to 0xdfffffff. This
portion of the address space is divided into three:
- mappings for dma_alloc_coherent()
- mappings for vmalloc() and ioremap()
- fixmap mappings, primarily used in copy_user_pages() to create
kernel mappings of user pages with the correct cache colour.
To optimise the TLB miss handler we don't want to add an additional
condition which checks whether the faulting address is in the user or
the kernel portion of the address space, and so all page tables have a
common portion which describes the kernel part of the address
space. As the SH4 uses a two level page table, only the kernel portion
of first level page table (the pgd entries) is duplicated. These all
point to the same second level entries (the pte's), and so no memory
is wasted.
The reference page table for the kernel is called the swapper_pg_dir,
and when a new page table is created for a new process the kernel
portion of the page table is copied from swapper_pg_dir. This works
fine when changes only occur in the second level of the kernel's page
table, or the first level entries are created before any new user
processes. However if a change occurs to the first level of the page
table, and there are existing processes which don't have this entry in
their page table, this new entry needs to be added. This is done on
demand, when the kernel accesses a P3 address which isn't mapped using
the current page table, the code in vmalloc_fault() copies the entry
from the reference page table (swapper_pg_dir) into the current
processes page table.
The bug which this patch addresses is that the code in vmalloc_fault()
was not copying addresses which fell in the dma_alloc_coherent()
portion of the address space, and it should have been copying any P3
address.
Why we hadn't seen this before, and what made this hard to reproduce,
is that normally the kernel will have called dma_alloc_coherent(), and
accessed the memory mapping created, before any user process
runs. Typically drivers such as USB or SATA will have created and used
mappings of this type during the kernel initialisation, when probing
for the attached devices, before init runs. Ethernet is slightly
different, as it normally only creates and accesses
dma_alloc_coherent() mappings when the network is brought up, but if
kernel level IP configuration is used this will also occur before any
user space process runs. So the first reproduction of this problem
which we saw was occurred when USB and SATA were removed from the
kernel, and then bring up Ethernet from user space using ifconfig.
I'd like to thank Joseph Bormolini who did the hard work reducing the
problem to this simple to reproduce criteria.
In your case the situation is slightly different, and turns out to
depends on the exact kernel configuration (which we had) and your
ramdisk contents (which we didn't - hence the need for some assumptions).
In this case the problem is a side effect of kernel level module
loading. Kernel subsystems sometimes trigger the load of kernel
modules directly, for example the crypto subsystem tries to load the
cryptomgr and MTD tries to load modules for Flash partitioning if
these are not built into the kernel. This is done by the kernel
creating a user process which runs insmod to try and load the
appropriate module.
In order for this to cause problems the system must be running with a
initrd or initramfs, which contains an insmod executable - if the
kernel can't find an insmod to run, no user process is created, and
the problem doesn't occur. If an insmod is found, a process is
created to run it, which will inherit the kernel portion of the
swapper_pg_dir first level page table. It doesn't matter whether the
inmod is successful or not, but when the the kernel scheduler context
switches back to the kernel initialisation thread, the insmod's mm is
'borrowed' by the kernel thread, as it doesn't have an address space
of its own. (Reference counting is used to ensure this mm is not
destroyed, even though the user process which caused its creation may no
longer exist.) If this address space doesn't have a first level page
table entry for the consistent mappings, and a driver tries to access
such a mapping, we are in the same situation as described above,
except this time in a kernel thread rather than a user thread
executing inside the kernel.
See bugzilla: 15425, 15836, 15862, 16106, 16793
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Revise the IP block reset process. This patch ensures that the
OCP_SYSCONFIG registers are reloaded after a custom reset. Since
OCP_SYSCONFIG bits are cleared during reset, they should be
reprogrammed unless the IP block is being left in reset. (The only IP
blocks that are left in reset are IP blocks with hardreset lines and
no custom reset function.) If the IP block is left in reset, then it
is inaccessible to the MPU, and an access to the OCP_SYSCONFIG
register will cause an abort.
This version incorporates comments from Omar Ramirez Luna
<omar.ramirez@ti.com> to skip the OCP_SYSCONFIG access after asserting
hardreset lines. This allows the MMU (IOMMU) IP block, which has
both hardreset lines and an OCP_SYSCONFIG register.
Also, ignore _ocp_softreset() errors if the IP block doesn't include a
softreset bit. This is needed since a subsequent patch will start
taking the return value of the _reset() function seriously.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
This implements basic -fstack-protector support, based on the early ARM
version in c743f38013. The SMP case is
limited to the initial canary value, while the UP case handles per-task
granularity (limited to 32-bit sh until a new enough sh64 compiler
manifests itself).
Signed-off-by: Filippo Arcidiacono <filippo.arcidiacono@st.com>
Reviewed-by: Carmelo Amoroso <carmelo.amoroso@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
My 9ce70c0240 "memcg: fix deadlock by inverting lrucare nesting" put a
nasty little bug into v3.3's version of mem_cgroup_replace_page_cache(),
sometimes used for FUSE. Replacing __mem_cgroup_commit_charge_lrucare()
by __mem_cgroup_commit_charge(), I used the "pc" pointer set up earlier:
but it's for oldpage, and needs now to be for newpage. Once oldpage was
freed, its PageCgroupUsed bit (cleared above but set again here) caused
"Bad page state" messages - and perhaps worse, being missed from newpage.
(I didn't find this by using FUSE, but in reusing the function for tmpfs.)
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: stable@vger.kernel.org [v3.3 only]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Through the transition to the auto-parser, the support for
Quanta/Gericom KN1 got broken. There are two problems behind it:
- This machine doesn't like the default COEF setup for ALC260 we take
now as default
- BIOS doesn't set the pins correctly at all; especially the machine
uses only the pin 0x0f for both headphone and speaker
This patch adds the fixup as a workaround for these issues.
Reported-and-tested-by: Uros Vampl <mobile.leecher@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Here is another fixes series for AT91 designed for 3.4-rc.
We experienced some issues while compiling some drivers as modules: Joachim has
corrected several of them. We may reduce this number of exported values by
reworking some drivers, in the future.
Some drivers are also modified here, I would like to keep them in the series
as the modifications are really related with our recent move to irqdomains or
simply related with compiler annotations.
I keep dmaengine Kconfig modification in this "fixes" series. The DMA
driver will not be available for 9x5 SoC family otherwise.
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
dmaengine: Kconfig: fix Atmel at_hdmac entry
USB: gadget/at91_udc: add gpio_to_irq() function to vbus interrupt
USB: ohci-at91: change annotations for probe/remove functions
leds-atmel-pwm.c: Make pwmled_probe() __devinit
ARM: at91: fix at91sam9261ek Ethernet dm9000 irq
ARM: at91: fix rm9200ek flash size
ARM: at91: remove empty at91_init_serial function
ARM: at91: fix typo in at91_pmc_base assembly declaration
ARM: at91: Export at91_matrix_base
ARM: at91: Export at91_pmc_base
ARM: at91: Export at91_ramc_base
ARM: at91: Export at91_st_base
* 'fixes-for-arm-soc-20120416' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: update defconfig
ARM: ux500: Fix unmet direct dependency
ARM: ux500: wake secondary cpu via resched
ARM i.MX misc fixes for -rc
* tag 'v3.4-rc3-imx-fixes' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM: imx: Fix imx5 idle logic bug
ARM: imx27-dt: Fix build due to removal of irq_domain_add_simple()
ARM: imx_v4_v5_defconfig: Add support for CONFIG_REGULATOR_FIXED_VOLTAGE
Fix regression for bad uart muxing and oops when PM is not set.
Revert one softreset regression and few other minor fixes.
* tag 'omap-fixes-for-v3.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP1: DMTIMER: fix broken timer clock source selection
ARM: OMAP: serial: Fix the ocp smart idlemode handling bug
ARM: OMAP2+: UART: Fix incorrect population of default uart pads
ARM: OMAP: sram: fix BUG in dpll code for !PM case
ARM: OMAP2/3: VENC hwmods: Remove OCPIF_SWSUP_IDLE flag from VENC slave interface
ARM: OMAP2+: hwmod: Revert "ARM: OMAP2+: hwmod: Make omap_hwmod_softreset wait for reset status"
ARM: OMAP2+: hwmod: add softreset delay field and OMAP4 data
ARM: OMAP1: mux: add missing include
This error appeared in the bcmring_defconfig build:
CC arch/arm/mach-bcmring/core.o
arch/arm/mach-bcmring/core.c:55: error: macro "AMBA_APB_DEVICE" requires 6 arguments, but only 5 given
arch/arm/mach-bcmring/core.c:55: warning: type defaults to 'int' in declaration of 'AMBA_APB_DEVICE'
arch/arm/mach-bcmring/core.c:56: error: macro "AMBA_APB_DEVICE" requires 6 arguments, but only 5 given
arch/arm/mach-bcmring/core.c:56: warning: type defaults to 'int' in declaration of 'AMBA_APB_DEVICE'
arch/arm/mach-bcmring/core.c:134: error: 'uartA_device' undeclared here (not in a function)
arch/arm/mach-bcmring/core.c:135: error: 'uartB_device' undeclared here (not in a function)
make[2]: *** [arch/arm/mach-bcmring/core.o] Error 1
It appeared as of commit 8ede1ae65e
"ARM: amba: bcmring: use common amba device initializers"
Note that in include/linux/amba/bus.h we have:
#define AMBA_APB_DEVICE(name, busid, id, base, irqs, data) ...
There is an a --> A case error in the busid and a missing zero
placeholder for the id field.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
[olof: reworded patch subject]
Signed-off-by: Olof Johansson <olof@lixom.net>
net/core/sysctl_net_core.c: In function ‘sysctl_core_init’:
net/core/sysctl_net_core.c:259: error: implicit declaration of function ‘kmemleak_not_leak’
with same error in net/ipv4/route.c
Signed-off-by: Shan Wei <davidshan@tencent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change fixes the compilation error triggered here for
i386 allmodconfig in linux-next:
http://kisskb.ellerman.id.au/kisskb/buildresult/6123842/
Logic attempting to predict the host architecture has been
removed from the Makefile. Instead, the bpf-direct sample
should now compile on any architecture, but if the architecture
is not supported, it will compile a minimal main() function.
This change also ensures the samples are not compiled when
there is no seccomp filter support.
(Note, I wasn't able to reproduce the error locally, but
the existing approach was clearly flawed. This tweak
should resolve your issue and avoid other future weirdness.)
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Suggested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Will Drewry <wad@chromium.org>
Signed-off-by: James Morris <james.l.morris@oracle.com>
This expands the available Yama ptrace restrictions to include two more
modes. Mode 2 requires CAP_SYS_PTRACE for PTRACE_ATTACH, and mode 3
completely disables PTRACE_ATTACH (and locks the sysctl).
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: James Morris <james.l.morris@oracle.com>
As pointed out by Jason Baron, when assigning a device to a guest
we first set the iommu domain pointer, which enables mapping
and unmapping of memory slots to the iommu. This leaves a window
where this path is enabled, but we haven't synchronized the iommu
mappings to the existing memory slots. Thus a slot being removed
at that point could send us down unexpected code paths removing
non-existent pinnings and iommu mappings. Take the slots_lock
around creating the iommu domain and initial mappings as well as
around iommu teardown to avoid this race.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Add missing "personality.h"
security/commoncap.c: In function 'cap_bprm_set_creds':
security/commoncap.c:510: error: 'PER_CLEAR_ON_SETID' undeclared (first use in this function)
security/commoncap.c:510: error: (Each undeclared identifier is reported only once
security/commoncap.c:510: error: for each function it appears in.)
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
kvm_set_shared_msr() may not be called in preemptible context,
but vmx_set_msr() does so:
BUG: using smp_processor_id() in preemptible [00000000] code: qemu-kvm/22713
caller is kvm_set_shared_msr+0x32/0xa0 [kvm]
Pid: 22713, comm: qemu-kvm Not tainted 3.4.0-rc3+ #39
Call Trace:
[<ffffffff8131fa82>] debug_smp_processor_id+0xe2/0x100
[<ffffffffa0328ae2>] kvm_set_shared_msr+0x32/0xa0 [kvm]
[<ffffffffa03a103b>] vmx_set_msr+0x28b/0x2d0 [kvm_intel]
...
Making kvm_set_shared_msr() work in preemptible is cleaner, but
it's used in the fast path. Making two variants is overkill, so
this patch just disables preemption around the call.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Its much cleaner to use PT_PAGE_TABLE_LEVEL than its numeric value.
Signed-off-by: Davidlohr Bueso <dave@gnu.org>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Remove the pseudo-hwmods associated with hardreset lines from the
OMAP4 data file. Future patches will convert this data to register
hwmods by interfaces, rather than registering hwmods directly. The
pseudo-hwmods aren't associated with any interfaces, so this will
create a problem.
After this change, the hwmod code will reset processor IPs at the
hwmod level, rather than by individual hardreset lines. So, for
example, if the IVA device driver code wishes to place one of the
sequencer cores into reset, while leaving the other active, it must do
so itself by calling the appropriate PRM functions.
This patch will cause a change in the initialization behavior of the
DSP, IVA, and IPU.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Parts of the hwmod code test to see if a module has one and only one
hardreset line before taking an action. It seems more appropriate
to control all hardreset lines associated with a hwmod, not just one.
It so happens that with the current hwmod data, this patch will not
change any behavior, since hwmods with hardreset lines have only one
hardreset line associated with them, and 'pseudo-hwmods' are used to
handle the other hardreset lines. But future hwmod data patches to
remove the pseudo-hwmods will change this.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Pull fuse updates from Miklos Szeredi.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: use flexible array in fuse.h
fuse: allow nanosecond granularity
fuse: O_DIRECT support for files
fuse: fix nlink after unlink
