Both OMAP4 and 5 exhibit the same revision ID in the REVISION register
but they have different number of ports i.e. 2 and 3 respectively.
So we can't rely on REVISION register for number of ports on OMAP5
and depend on platform data (or device tree) instead.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Let's have a single platform data structure for the OMAP's High-Speed
USB host subsystem instead of having 3 separate ones i.e. one for
board data, one for USB Host (UHH) module and one for USB-TLL module.
This makes the code much simpler and avoids creating multiple copies of
platform data.
Part 1 touches platform headers
Part 2 touches drivers
Part 3 touches platform data
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
The CPSW switch can act as Dual EMAC by segregating the switch ports
using VLAN and port VLAN as per the TRM description in
14.3.2.10.2 Dual Mac Mode
Following CPSW components will be common for both the interfaces.
* Interrupt source is common for both eth interfaces
* Interrupt pacing is common for both interfaces
* Hardware statistics is common for all the ports
* CPDMA is common for both eth interface
* CPTS is common for both the interface and it should not be enabled on
both the interface as timestamping information doesn't contain port
information.
Constrains
* Reserved VID of One port should not be used in other interface which will
enable switching functionality
* Same VID must not be used in both the interface which will enable switching
functionality
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This the basic functional Invensense MPU6050 Device driver.
Signed-off-by: Ge Gao <ggao@invensense.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch introduces using temperature falling interrupt in exynos
thermal driver. Former patch, it only use polling way to check
whether if system themperature is fallen. However, exynos SOC also
provides temperature falling interrupt way to do same things by hw.
This feature is not supported in exynos4210.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch supports basic common driver code for LP5521, LP5523/55231 devices.
( Driver Structure Data )
lp55xx_led and lp55xx_chip
In lp55xx common driver, two different data structure is used.
o lp55xx_led
control multi output LED channels such as led current, channel index.
o lp55xx_chip
general chip control such like the I2C and platform data.
For example, LP5521 has maximum 3 LED channels.
LP5523/55231 has 9 output channels.
lp55xx_chip for LP5521 ... lp55xx_led #1
lp55xx_led #2
lp55xx_led #3
lp55xx_chip for LP5523 ... lp55xx_led #1
lp55xx_led #2
.
.
lp55xx_led #9
( Platform Data )
LP5521 and LP5523/55231 have own specific platform data.
However, this data can be handled with just one platform data structure.
The lp55xx platform data is declared in the header.
This structure is derived from leds-lp5521.h and leds-lp5523.h
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
adding support for VLAN interface for cpsw.
CPSW VLAN Capability
* Can filter VLAN packets in Hardware
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for MAX6581, MAX6602, MAX6622, MAX6636, MAX6689, MAX6693,
MAX6694, MAX6697, MAX6698, and MAX6699 temperature sensors
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
This is the Renesas IPMMU driver and IOMMU API implementation.
The IPMMU module supports the MMU function and the PMB function. The
MMU function provides address translation by pagetable compatible with
ARMv6. The PMB function provides address translation including
tile-linear translation. This patch implements the MMU function.
The iommu driver does not register a platform driver directly because:
- the register space of the MMU function and the PMB function
have a common register (used for settings flush), so they should ideally
have a way to appropriately share this register.
- the MMU function uses the IOMMU API while the PMB function does not.
- the two functions may be used independently.
Signed-off-by: Hideki EIRAKU <hdk@igel.co.jp>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
From Tony Lindgren:
OMAP GPMC (General Purpose Memory Controller) changes to add
device tree bindings.
* tag 'omap-for-v3.9/gpmc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: gpmc: Add device tree documentation for elm handle
ARM: OMAP2+: gpmc: add DT bindings for OneNAND
ARM: OMAP2+: gpmc-onenand: drop __init annotation
mtd: omap-onenand: pass device_node in platform data
ARM: OMAP2+: Prevent potential crash if GPMC probe fails
ARM: OMAP2+: gpmc: Remove unneeded of_node_put()
ARM: OMAP: gpmc: add DT bindings for GPMC timings and NAND
ARM: OMAP: gpmc: enable hwecc for AM33xx SoCs
ARM: OMAP: gpmc-nand: drop __init annotation
mtd: omap-nand: pass device_node in platform data
ARM: OMAP: gpmc: don't create devices from initcall on DT
Signed-off-by: Olof Johansson <olof@lixom.net>
Minor features and bug fixes for PXA, OMAP and GPIO deivce drivers and a
cosmetic change to the bitbang driver.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
ELM module can be used for hardware error correction of BCH 4 & 8 bit.
ELM module functionality is verified by checking the availability of
handle for ELM module in device tree. Hence supporting
1. ELM module available, BCH error correction done by ELM module. Also
support read & write page in one shot by adding custom read_page and
write_page methods. This helps in optimizing code for NAND flashes with
page size less than 4 KB.
2. If ELM module not available fall back to software BCH error
correction support.
New structure member is added to omap_nand_info
1. "is_elm_used" to know the status of whether the ELM module is used for
error correction or not.
2. "elm_dev" device pointer to elm device on detection of ELM module.
Also being here update the device tree documentation of gpmc-nand for
adding optional property elm_id.
Note:
ECC layout uses 1 extra bytes for 512 byte of data to handle erased
pages. Extra byte programmed to zero for programmed pages. Also BCH8
requires 14 byte ecc to maintain compatibility with RBL ECC layout.
This results a common ecc layout across RBL, U-boot & Linux with BCH8.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The ELM hardware module can be used to speedup BCH 4/8/16 ECC scheme
error correction.
For now only 4 & 8 bit support is added
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Inside Secure microread is an HCI based NFC chipset.
This initial support includes reader and p2p (Target and initiator) modes.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Pass an optional device_node pointer in the platform data,
which in turn will be put into a mtd_part_parser_data.
This way, code that sets up the platform devices can pass
along the node from DT so that the partitions can be parsed.
For non-DT boards, this change has no effect.
Acked-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
From Pawel Moll:
Versatile Express related driver updates for 3.9:
* Move sp810 header to a more generic location,
mainly to share it with arm64
* tag 'vexpress/drivers-for-3.9' of git://git.linaro.org/people/pawelmoll/linux:
arm: Move sp810.h to include/linux/amba/
+ Linux 3.8-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
This driver is simple, uses the latest interfaces and contains few if
any controversial elements. All of its interfaces have been in place
for a long time now. Hence let's move it out of staging.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Peter Meerwald <pmeerw@pmeerw.net>
This patch allows the board code to define SPI devices which needs to
toggle the chip select after every word send. This is needed to get a
better resolution reading e.g. an ADC data stream.
Apart from that, as in the normal code CS is controlled by software,
a transfer is done much faster.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Felipe writes:
usb: xceiv: patches for v3.9 merge window
Two new PHY drivers coming here: one for Samsung,
one for OMAP. Both architectures are adding USB3
support to mainline kernel.
The PHY layer now allows us to have mulitple PHYs
of the same type, which is necessary for platforms
which provide more than one USB peripheral port.
There's also a few cleanups here: removal of __dev*
annotations, conversion of a cast to to_delayed_work(),
and mxs-phy learns about ->set_suspend.
This driver uses usb_phy interface to interact with s3c-hsotg. Supports
phy_init and phy_shutdown functions to enable/disable usb phy. Support
will be extended to host controllers and more Samsung SoCs.
Signed-off-by: Praveen Paneri <p.paneri@samsung.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds support for polling work mode, i.e. system is perform
periodical check chip status when IRQ-line is not connected to CPU.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pass an optional device_node pointer in the platform data, which in turn
will be put into a mtd_part_parser_data. This way, code that sets up the
platform devices can pass along the node from DT so that the partitions
can be parsed.
For non-DT boards, this change has no effect.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Artem Bityutskiy <dedekind1@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch add support to manage LLI by SW for select phy channels.
There is a HW issue in certain controllers due to which on certain
occassions HW LLI cannot be used on some physical channels. To avoid
the HW issue on a specific phy channel, the phy channel number can be
added to the list of soft_lli_channels and there after all the transfers
on that channel will use software LLI, for peripheral to memory
transfers.
SoftLLI introduces relink overhead, that could impact performace for
certain use cases.
This is based on a previous patch of Narayanan Gopalakrishnan.
Cc: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
DMAC_ICFG[0:2]=SCHNB only allows to count 'multiple of 4' physical
channels so it was ok with platforms having 8 channels but cannot be
used for next versions (with 10 or 14 channels). This patch allows to
provide the number of physical channels for a DMA device via
platform_data, or still rely on SCHNB if platform_data announces 0
channel.
Signed-off-by: Gerald Baeza <gerald.baeza@stericsson.com>
Reviewed-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
This patch adds new driver of SMSC USB3503 USB 2.0 hub controller with HSIC
upstream connectivity and three USB 2.0 downstream ports. The specification
can be found from 'http://www.smsc.com/index.php?tid=295&pid=325'.
The current version have been tested very basic features switching the modes,
HUB-MODE and STANDBY-MODE.
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c045e3f13 (ARM: imx: include iram.h rather than mach/iram.h) changed the
location of iram.h, which causes the following build error when building the coda
driver:
drivers/media/platform/coda.c:27:23: error: mach/iram.h: No such file or directory
drivers/media/platform/coda.c: In function 'coda_probe':
drivers/media/platform/coda.c:2000: error: implicit declaration of function 'iram_alloc'
drivers/media/platform/coda.c:2001: warning: assignment makes pointer from integer without a cast
drivers/media/platform/coda.c: In function 'coda_remove':
drivers/media/platform/coda.c:2024: error: implicit declaration of function 'iram_free'
Since the content of iram.h is not imx specific, move it to
include/linux/platform_data/imx-iram.h instead. This is an intermediate solution
until the i.MX iram allocator is converted to the generic SRAM allocator.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This extracts the platform data that we will keep generic
from the U300 platform and associates it with the COH901318
driver in <linux/platform_data/dma-coh901318.h>.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch is for new lp8755 regulator dirver and
several unsed variables were deleted and then test was done.
LP8755 :
The LP8755 is a high performance power management unit.It contains
six step-down DC-DC converters which can can be filexibly bundled
together in multiphase converters as required by application.
www.ti.com
Signed-off-by: Daniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pull IOMMU updates from Joerg Roedel:
"A few new features this merge-window. The most important one is
probably, that dma-debug now warns if a dma-handle is not checked with
dma_mapping_error by the device driver. This requires minor changes
to some architectures which make use of dma-debug. Most of these
changes have the respective Acks by the Arch-Maintainers.
Besides that there are updates to the AMD IOMMU driver for refactor
the IOMMU-Groups support and to make sure it does not trigger a
hardware erratum.
The OMAP changes (for which I pulled in a branch from Tony Lindgren's
tree) have a conflict in linux-next with the arm-soc tree. The
conflict is in the file arch/arm/mach-omap2/clock44xx_data.c which is
deleted in the arm-soc tree. It is safe to delete the file too so
solve the conflict. Similar changes are done in the arm-soc tree in
the common clock framework migration. A missing hunk from the patch
in the IOMMU tree will be submitted as a seperate patch when the
merge-window is closed."
* tag 'iommu-updates-v3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (29 commits)
ARM: dma-mapping: support debug_dma_mapping_error
ARM: OMAP4: hwmod data: ipu and dsp to use parent clocks instead of leaf clocks
iommu/omap: Adapt to runtime pm
iommu/omap: Migrate to hwmod framework
iommu/omap: Keep mmu enabled when requested
iommu/omap: Remove redundant clock handling on ISR
iommu/amd: Remove obsolete comment
iommu/amd: Don't use 512GB pages
iommu/tegra: smmu: Move bus_set_iommu after probe for multi arch
iommu/tegra: gart: Move bus_set_iommu after probe for multi arch
iommu/tegra: smmu: Remove unnecessary PTC/TLB flush all
tile: dma_debug: add debug_dma_mapping_error support
sh: dma_debug: add debug_dma_mapping_error support
powerpc: dma_debug: add debug_dma_mapping_error support
mips: dma_debug: add debug_dma_mapping_error support
microblaze: dma-mapping: support debug_dma_mapping_error
ia64: dma_debug: add debug_dma_mapping_error support
c6x: dma_debug: add debug_dma_mapping_error support
ARM64: dma_debug: add debug_dma_mapping_error support
intel-iommu: Prevent devices with RMRRs from being placed into SI Domain
...
Pull ARM SoC fixes from Olof Johansson:
"This is a batch of fixes for arm-soc platforms, most of it is for OMAP
but there are others too (i.MX, Tegra, ep93xx). Fixes warnings, some
broken platforms and drivers, etc. A bit all over the map really."
There was some concern about commit 68136b10 ("RM: sunxi: Change device
tree naming scheme for sunxi"), but Tony says:
"Looks like that's trivial to fix as needed, no need to rebuild the
branch to fix that AFAIK.
The fix can be done once Olof is available online again.
Linus, I suggest that you go ahead and pull this if there are no other
issues with this branch."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
ARM: sunxi: Change device tree naming scheme for sunxi
ARM: ux500: fix missing include
ARM: u300: delete custom pin hog code
ARM: davinci: fix build break due to missing include
ARM: exynos: Fix warning due to missing 'inline' in stub
ARM: imx: Move platform-mx2-emma to arch/arm/mach-imx/devices
ARM i.MX51 clock: Fix regression since enabling MIPI/HSP clocks
ARM: dts: mx27: Fix the AIPI bus for FEC
ARM: OMAP2+: common: remove use of vram
ARM: OMAP3/4: cpuidle: fix sparse and checkpatch warnings
ARM: OMAP4: clock data: DPLLs are missing bypass clocks in their parent lists
ARM: OMAP4: clock data: div_iva_hs_clk is a power-of-two divider
ARM: OMAP4: Fix EMU clock domain always on
ARM: OMAP4460: Workaround ABE DPLL failing to turn-on
ARM: OMAP4: Enhance support for DPLLs with 4X multiplier
ARM: OMAP4: Add function table for non-M4X dplls
ARM: OMAP4: Update timer clock aliases
ARM: OMAP: Move plat/omap-serial.h to include/linux/platform_data/serial-omap.h
ARM: dts: Add build target for omap4-panda-a4
ARM: dts: OMAP2420: Correct H4 board memory size
...
Pull MTD updates from David Woodhouse:
- Various cleanups especially in NAND tests
- Add support for NAND flash on BCMA bus
- DT support for sh_flctl and denali NAND drivers
- Kill obsolete/superceded drivers (fortunet, nomadik_nand)
- Fix JFFS2 locking bug in ENOMEM failure path
- New SPI flash chips, as usual
- Support writing in 'reliable mode' for DiskOnChip G4
- Debugfs support in nandsim
* tag 'for-linus-20121219' of git://git.infradead.org/linux-mtd: (96 commits)
mtd: nand: typo in nand_id_has_period() comments
mtd: nand/gpio: use io{read,write}*_rep accessors
mtd: block2mtd: throttle writes by calling balance_dirty_pages_ratelimited.
mtd: nand: gpmi: reset BCH earlier, too, to avoid NAND startup problems
mtd: nand/docg4: fix and improve read of factory bbt
mtd: nand/docg4: reserve bb marker area in ecclayout
mtd: nand/docg4: add support for writing in reliable mode
mtd: mxc_nand: reorder part_probes to let cmdline override other sources
mtd: mxc_nand: fix unbalanced clk_disable() in error path
mtd: nandsim: Introduce debugfs infrastructure
mtd: physmap_of: error checking to prevent a NULL pointer dereference
mtg: docg3: potential divide by zero in doc_write_oob()
mtd: bcm47xxnflash: writing support
mtd: tests/read: initialize buffer for whole next page
mtd: at91: atmel_nand: return bit flips for the PMECC read_page()
mtd: fix recovery after failed write-buffer operation in cfi_cmdset_0002.c
mtd: nand: onfi need to be probed in 8 bits mode
mtd: nand: add NAND_BUSWIDTH_AUTO to autodetect bus width
mtd: nand: print flash size during detection
mted: nand_wait_ready timeout fix
...
Pull i2c-embedded changes from Wolfram Sang:
- CBUS driver (an I2C variant)
- continued rework of the omap driver
- s3c2410 gets lots of fixes and gains pinctrl support
- at91 gains DMA support
- the GPIO muxer gains devicetree probing
- typical fixes and additions all over
* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (45 commits)
i2c: omap: Remove the OMAP_I2C_FLAG_RESET_REGS_POSTIDLE flag
i2c: at91: add dma support
i2c: at91: change struct members indentation
i2c: at91: fix compilation warning
i2c: mxs: Do not disable the I2C SMBus quick mode
i2c: mxs: Handle i2c DMA failure properly
i2c: s3c2410: Remove recently introduced performance overheads
i2c: ocores: Move grlib set/get functions into #ifdef CONFIG_OF block
i2c: s3c2410: Add fix for i2c suspend/resume
i2c: s3c2410: Fix code to free gpios
i2c: i2c-cbus-gpio: introduce driver
i2c: ocores: Add support for the GRLIB port of the controller and use function pointers for getreg and setreg functions
i2c: ocores: Add irq support for sparc
i2c: omap: Move the remove constraint
ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049
i2c: s3c2410: do not special case HDMIPHY stuck bus detection
i2c: s3c2410: use exponential back off while polling for bus idle
i2c: s3c2410: do not generate STOP for QUIRK_HDMIPHY
i2c: s3c2410: grab adapter lock while changing i2c clock
i2c: s3c2410: Add support for pinctrl
...
From Tony Lindgren:
These patches fixes a build error caused by a merge
conflict with the fb code, few timer warnings, and longer
term regressions for tfp410 and omap h4 ethernet. Also
included is a GPIO mode fix for the legacy mux code.
* tag 'omap-for-v3.8/fixes-for-merge-window-v4-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: common: remove use of vram
ARM: OMAP: Move plat/omap-serial.h to include/linux/platform_data/serial-omap.h
ARM: dts: Add build target for omap4-panda-a4
ARM: dts: OMAP2420: Correct H4 board memory size
mfd: omap-usb-host: get rid of cpu_is_omap..() macros
ARM: OMAP: Remove debug-devices.c
ARM: OMAP2420: Fix ethernet support for OMAP2420 H4
OMAP2+: mux: Fixed gpio mux mode analysis
OMAP: board-files: fix i2c_bus for tfp410
ARM: OMAP2+: Fix sparse warnings in timer.c
ARM: AM335x: Fix warning in timer.c
ARM: OMAP2+: Fix realtime_counter_init warning in timer.c
The LP855x family devices support the PWM input for the backlight control.
Period of the PWM is configurable in the platform side. Platform
specific functions are unnecessary anymore because generic PWM functions
are used inside the driver.
(PWM input mode)
To set the brightness, new lp855x_pwm_ctrl() is used.
If a PWM device is not allocated, devm_pwm_get() is called.
The PWM consumer name is from the chip name such as 'lp8550' and 'lp8556'.
To get the brightness value, no additional handling is required.
Just the value of 'props.brightness' is returned.
If the PWM driver is not ready while initializing the LP855x driver, it's
OK. The PWM device can be retrieved later, when the brightness value is
changed.
Documentation is updated with an example.
[akpm@linux-foundation.org: coding-style simplification, per Thierry]
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Bryan Wu <bryan.wu@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull MFS update from Samuel Ortiz:
"This is the MFD patch set for the 3.8 merge window.
We have several new drivers, most of the time coming with their sub
devices drivers:
- Austria Microsystem's AS3711
- Nano River's viperboard
- TI's TPS80031, AM335x TS/ADC,
- Realtek's MMC/memstick card reader
- Nokia's retu
We also got some notable cleanups and improvements:
- tps6586x got converted to IRQ domains.
- tps65910 and tps65090 moved to the regmap IRQ API.
- STMPE is now Device Tree aware.
- A general twl6040 and twl-core cleanup, with moves to the regmap
I/O and IRQ APIs and a conversion to the recently added PWM
framework.
- sta2x11 gained regmap support.
Then the rest is mostly tiny cleanups and fixes, among which we have
Mark's wm5xxx and wm8xxx patchset."
Far amount of annoying but largely trivial conflicts. Many due to
__devinit/exit removal, others due to one or two of the new drivers also
having come in through another tree.
* tag 'mfd-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (119 commits)
mfd: tps6507x: Convert to devm_kzalloc
mfd: stmpe: Update DT support for stmpe driver
mfd: wm5102: Add readback of DSP status 3 register
mfd: arizona: Log if we fail to create the primary IRQ domain
mfd: tps80031: MFD_TPS80031 needs to select REGMAP_IRQ
mfd: tps80031: Add terminating entry for tps80031_id_table
mfd: sta2x11: Fix potential NULL pointer dereference in __sta2x11_mfd_mask()
mfd: wm5102: Add tuning for revision B
mfd: arizona: Defer patch initialistation until after first device boot
mfd: tps65910: Fix wrong ack_base register
mfd: tps65910: Remove unused data
mfd: stmpe: Get rid of irq_invert_polarity
mfd: ab8500-core: Fix invalid free of devm_ allocated data
mfd: wm5102: Mark DSP memory regions as volatile
mfd: wm5102: Correct default for LDO1_CONTROL_2
mfd: arizona: Register haptics devices
mfd: wm8994: Make current device behaviour the default
mfd: tps65090: MFD_TPS65090 needs to select REGMAP_IRQ
mfd: Fix stmpe.c build when OF is not enabled
mfd: jz4740-adc: Use devm_kzalloc
...
Pull ARM SoC updates for Marvell mvebu/kirkwood from Olof Johansson:
"This is a branch with updates for Marvell's mvebu/kirkwood platforms.
They came in late-ish, and were heavily interdependent such that it
didn't make sense to split them up across the cross-platform topic
branches. So here they are (for the second release in a row) in a
branch on their own."
* tag 'mvebu' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (88 commits)
arm: l2x0: add aurora related properties to OF binding
arm: mvebu: add Aurora L2 Cache Controller to the DT
arm: mvebu: add L2 cache support
dma: mv_xor: fix error handling path
dma: mv_xor: fix error checking of irq_of_parse_and_map()
dma: mv_xor: use request_irq() instead of devm_request_irq()
dma: mv_xor: clear the window override control registers
arm: mvebu: fix address decoding armada_cfg_base() function
ARM: mvebu: update defconfig with I2C and RTC support
ARM: mvebu: Add SATA support for OpenBlocks AX3-4
ARM: mvebu: Add support for the RTC in OpenBlocks AX3-4
ARM: mvebu: Add support for I2C on OpenBlocks AX3-4
ARM: mvebu: Add support for I2C controllers in Armada 370/XP
arm: mvebu: Add hardware I/O Coherency support
arm: plat-orion: Add coherency attribute when setup mbus target
arm: dma mapping: Export a dma ops function arm_dma_set_mask
arm: mvebu: Add SMP support for Armada XP
arm: mm: Add support for PJ4B cpu and init routines
arm: mvebu: Add IPI support via doorbells
arm: mvebu: Add initial support for power managmement service unit
...
Instead of using cpu_is_omap..() macros in the device driver we
rely on information provided in the platform data.
The only information we need is whether the USB Host module has
a single ULPI bypass control bit for all ports or individual bypass
control bits for each port. OMAP3 REV2.1 and earlier have the former.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
[tony@atomide.com: updated to remove plat/cpu.h]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull SPI updates from Grant Likely:
"Primarily SPI device driver bug fixes, one removal of an old driver,
and some new tegra support. There is some core code change too, but
all in all pretty small stuff.
The new features to note are:
- Common code for describing GPIO CS lines in the device tree
- Remove the SPI_BUFSIZ limitation on spi_write_the_read()
- core spi ensures bits_per_word is set correctly
- SPARC can now use SPI"
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6: (36 commits)
spi/sparc: Allow of_register_spi_devices for sparc
spi: Remove HOTPLUG section attributes
spi: Add support for specifying 3-wire mode via device tree
spi: Fix comparison of different integer types
spi/orion: Add SPI_CHPA and SPI_CPOL support to kirkwood driver.
spi/sh: Add SH Mobile series as dependency to MSIOF controller
spi/sh-msiof: Remove unneeded clock name
spi: Remove SPI_BUFSIZ restriction on spi_write_then_read()
spi/stmp: remove obsolete driver
spi/clps711x: New SPI master driver
spi: omap2-mcspi: remove duplicate inclusion of linux/err.h
spi: omap2-mcspi: Fix the redifine warning
spi/sh-hspi: add CS manual control support
of_spi: add generic binding support to specify cs gpio
spi: omap2-mcspi: remove duplicated include from spi-omap2-mcspi.c
spi/bitbang: (cosmetic) simplify list manipulation
spi/bitbang: avoid needless loop flow manipulations
spi/omap: fix D0/D1 direction confusion
spi: tegra: add spi driver for sflash controller
spi: Dont call master->setup if not populated
...
Pull sound updates from Takashi Iwai:
"This update contains a fairly wide range of changes all over in sound
subdirectory, mainly because of UAPI header moves by David and __dev*
annotation removals by Bill. Other highlights are:
- Introduced the support for wallclock timestamps in ALSA PCM core
- Add the poll loop implementation for HD-audio jack detection
- Yet more VGA-switcheroo fixes for HD-audio
- New VIA HD-audio codec support
- More fixes on resource management in USB audio and MIDI drivers
- More quirks for USB-audio ASUS Xonar U3, Reloop Play, Focusrite,
Roland VG-99, etc
- Add support for FastTrack C400 usb-audio
- Clean ups in many drivers regarding firmware loading
- Add PSC724 Ultiimate Edge support to ice1712
- A few hdspm driver updates
- New Stanton SCS.1d/1m FireWire driver
- Standardisation of the logging in ASoC codes
- DT and dmaengine support for ASoC Atmel
- Support for Wolfson ADSP cores
- New drivers for Freescale/iVeia P1022 and Maxim MAX98090
- Lots of other ASoC driver fixes and developments"
Fix up trivial conflicts. And go out on a limb and assume the dts file
'status' field of one of the conflicting things was supposed to be
"disabled", not "disable" like in pretty much all other cases.
* tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (341 commits)
ALSA: hda - Move runtime PM check to runtime_idle callback
ALSA: hda - Add stereo-dmic fixup for Acer Aspire One 522
ALSA: hda - Avoid doubly suspend after vga switcheroo
ALSA: usb-audio: Enable S/PDIF on the ASUS Xonar U3
ALSA: hda - Check validity of CORB/RIRB WP reads
ALSA: hda - use usleep_range in link reset and change timeout check
ALSA: HDA: VIA: Add support for codec VT1808.
ALSA: HDA: VIA Add support for codec VT1705CF.
ASoC: codecs: remove __dev* attributes
ASoC: utils: remove __dev* attributes
ASoC: ux500: remove __dev* attributes
ASoC: txx9: remove __dev* attributes
ASoC: tegra: remove __dev* attributes
ASoC: spear: remove __dev* attributes
ASoC: sh: remove __dev* attributes
ASoC: s6000: remove __dev* attributes
ASoC: OMAP: remove __dev* attributes
ASoC: nuc900: remove __dev* attributes
ASoC: mxs: remove __dev* attributes
ASoC: kirkwood: remove __dev* attributes
...
Pull ARM SoC multiplatform conversion patches from Olof Johansson:
"Here are more patches in the progression towards multiplatform, sparse
irq conversions in particular.
Tegra has a handful of cleanups and general groundwork, but is not
quite there yet on full enablement.
Platforms that are enabled through this branch are VT8500 and Zynq.
Note that i.MX was converted in one of the earlier cleanup branches as
well (before we started a separate topic for multiplatform). And both
new platforms for this merge window, sunxi and bcm, were merged with
multiplatform support enabled."
Fix up conflicts mostly as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
ARM: zynq: Remove all unused mach headers
ARM: zynq: add support for ARCH_MULTIPLATFORM
ARM: zynq: make use of debug_ll_io_init()
ARM: zynq: remove TTC early mapping
ARM: tegra: move debug-macro.S to include/debug
ARM: tegra: don't include iomap.h from debug-macro.S
ARM: tegra: decouple uncompress.h and debug-macro.S
ARM: tegra: simplify DEBUG_LL UART selection options
ARM: tegra: select SPARSE_IRQ
ARM: tegra: enhance timer.c to get IO address from device tree
ARM: tegra: enhance timer.c to get IRQ info from device tree
ARM: timer: fix checkpatch warnings
ARM: tegra: add TWD to device tree
ARM: tegra: define DT bindings for and instantiate RTC
ARM: tegra: define DT bindings for and instantiate timer
clocksource/mtu-nomadik: use apb_pclk
clk: ux500: Register mtu apb_pclocks
ARM: plat-nomadik: convert platforms to SPARSE_IRQ
mfd/db8500-prcmu: use the irq_domain_add_simple()
mfd/ab8500-core: use irq_domain_add_simple()
...
Pull networking changes from David Miller:
1) Allow to dump, monitor, and change the bridge multicast database
using netlink. From Cong Wang.
2) RFC 5961 TCP blind data injection attack mitigation, from Eric
Dumazet.
3) Networking user namespace support from Eric W. Biederman.
4) tuntap/virtio-net multiqueue support by Jason Wang.
5) Support for checksum offload of encapsulated packets (basically,
tunneled traffic can still be checksummed by HW). From Joseph
Gasparakis.
6) Allow BPF filter access to VLAN tags, from Eric Dumazet and
Daniel Borkmann.
7) Bridge port parameters over netlink and BPDU blocking support
from Stephen Hemminger.
8) Improve data access patterns during inet socket demux by rearranging
socket layout, from Eric Dumazet.
9) TIPC protocol updates and cleanups from Ying Xue, Paul Gortmaker, and
Jon Maloy.
10) Update TCP socket hash sizing to be more in line with current day
realities. The existing heurstics were choosen a decade ago.
From Eric Dumazet.
11) Fix races, queue bloat, and excessive wakeups in ATM and
associated drivers, from Krzysztof Mazur and David Woodhouse.
12) Support DOVE (Distributed Overlay Virtual Ethernet) extensions
in VXLAN driver, from David Stevens.
13) Add "oops_only" mode to netconsole, from Amerigo Wang.
14) Support set and query of VEB/VEPA bridge mode via PF_BRIDGE, also
allow DCB netlink to work on namespaces other than the initial
namespace. From John Fastabend.
15) Support PTP in the Tigon3 driver, from Matt Carlson.
16) tun/vhost zero copy fixes and improvements, plus turn it on
by default, from Michael S. Tsirkin.
17) Support per-association statistics in SCTP, from Michele
Baldessari.
And many, many, driver updates, cleanups, and improvements. Too
numerous to mention individually.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
net/mlx4_en: Add support for destination MAC in steering rules
net/mlx4_en: Use generic etherdevice.h functions.
net: ethtool: Add destination MAC address to flow steering API
bridge: add support of adding and deleting mdb entries
bridge: notify mdb changes via netlink
ndisc: Unexport ndisc_{build,send}_skb().
uapi: add missing netconf.h to export list
pkt_sched: avoid requeues if possible
solos-pci: fix double-free of TX skb in DMA mode
bnx2: Fix accidental reversions.
bna: Driver Version Updated to 3.1.2.1
bna: Firmware update
bna: Add RX State
bna: Rx Page Based Allocation
bna: TX Intr Coalescing Fix
bna: Tx and Rx Optimizations
bna: Code Cleanup and Enhancements
ath9k: check pdata variable before dereferencing it
ath5k: RX timestamp is reported at end of frame
ath9k_htc: RX timestamp is reported at end of frame
...
Pull ARM SoC updates from Olof Johansson:
"This contains the bulk of new SoC development for this merge window.
Two new platforms have been added, the sunxi platforms (Allwinner A1x
SoCs) by Maxime Ripard, and a generic Broadcom platform for a new
series of ARMv7 platforms from them, where the hope is that we can
keep the platform code generic enough to have them all share one mach
directory. The new Broadcom platform is contributed by Christian
Daudt.
Highbank has grown support for Calxeda's next generation of hardware,
ECX-2000.
clps711x has seen a lot of cleanup from Alexander Shiyan, and he's
also taken on maintainership of the platform.
Beyond this there has been a bunch of work from a number of people on
converting more platforms to IRQ domains, pinctrl conversion, cleanup
and general feature enablement across most of the active platforms."
Fix up trivial conflicts as per Olof.
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (174 commits)
mfd: vexpress-sysreg: Remove LEDs code
irqchip: irq-sunxi: Add terminating entry for sunxi_irq_dt_ids
clocksource: sunxi_timer: Add terminating entry for sunxi_timer_dt_ids
irq: versatile: delete dangling variable
ARM: sunxi: add missing include for mdelay()
ARM: EXYNOS: Avoid early use of of_machine_is_compatible()
ARM: dts: add node for PL330 MDMA1 controller for exynos4
ARM: EXYNOS: Add support for secondary CPU bring-up on Exynos4412
ARM: EXYNOS: add UART3 to DEBUG_LL ports
ARM: S3C24XX: Add clkdev entry for camif-upll clock
ARM: SAMSUNG: Add s3c24xx/s3c64xx CAMIF GPIO setup helpers
ARM: sunxi: Add missing sun4i.dtsi file
pinctrl: samsung: Do not initialise statics to 0
ARM i.MX6: remove gate_mask from pllv3
ARM i.MX6: Fix ethernet PLL clocks
ARM i.MX6: rename PLLs according to datasheet
ARM i.MX6: Add pwm support
ARM i.MX51: Add pwm support
ARM i.MX53: Add pwm support
ARM: mx5: Replace clk_register_clkdev with clock DT lookup
...
Pull ARM SoC cleanups on various subarchitectures from Olof Johansson:
"Cleanup patches for various ARM platforms and some of their associated
drivers. There's also a branch in here that enables Freescale i.MX to
be part of the multiplatform support -- the first "big" SoC that is
moved over (more multiplatform work comes in a separate branch later
during the merge window)."
Conflicts fixed as per Olof, including a silent semantic one in
arch/arm/mach-omap2/board-generic.c (omap_prcm_restart() was renamed to
omap3xxx_restart(), and a new user of the old name was added).
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (189 commits)
ARM: omap: fix typo on timer cleanup
ARM: EXYNOS: Remove unused regs-mem.h file
ARM: EXYNOS: Remove unused non-dt support for dwmci controller
ARM: Kirkwood: Use hw_pci.ops instead of hw_pci.scan
ARM: OMAP3: cm-t3517: use GPTIMER for system clock
ARM: OMAP2+: timer: remove CONFIG_OMAP_32K_TIMER
ARM: SAMSUNG: use devm_ functions for ADC driver
ARM: EXYNOS: no duplicate mask/unmask in eint0_15
ARM: S3C24XX: SPI clock channel setup is fixed for S3C2443
ARM: EXYNOS: Remove i2c0 resource information and setting of device names
ARM: Kirkwood: checkpatch cleanups
ARM: Kirkwood: Fix sparse warnings.
ARM: Kirkwood: Remove unused includes
ARM: kirkwood: cleanup lsxl board includes
ARM: integrator: use BUG_ON where possible
ARM: integrator: push down SC dependencies
ARM: integrator: delete static UART1 mapping
ARM: integrator: delete SC mapping on the CP
ARM: integrator: remove static CP syscon mapping
ARM: integrator: remove static AP syscon mapping
...
Pull ARM SoC Header cleanups from Olof Johansson:
"This is a collection of header file cleanups, mostly for OMAP and
AT91, that keeps moving the platforms in the direction of
multiplatform by removing the need for mach-dependent header files
used in drivers and other places."
Fix up mostly trivial conflicts as per Olof.
* tag 'headers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (106 commits)
ARM: OMAP2+: Move iommu/iovmm headers to platform_data
ARM: OMAP2+: Make some definitions local
ARM: OMAP2+: Move iommu2 to drivers/iommu/omap-iommu2.c
ARM: OMAP2+: Move plat/iovmm.h to include/linux/omap-iommu.h
ARM: OMAP2+: Move iopgtable header to drivers/iommu/
ARM: OMAP: Merge iommu2.h into iommu.h
atmel: move ATMEL_MAX_UART to platform_data/atmel.h
ARM: OMAP: Remove omap_init_consistent_dma_size()
arm: at91: move at91rm9200 rtc header in drivers/rtc
arm: at91: move reset controller header to arm/arm/mach-at91
arm: at91: move pit define to the driver
arm: at91: move at91_shdwc.h to arch/arm/mach-at91
arm: at91: move board header to arch/arm/mach-at91
arn: at91: move at91_tc.h to arch/arm/mach-at91
arm: at91 move at91_aic.h to arch/arm/mach-at91
arm: at91 move board.h to arch/arm/mach-at91
arm: at91: move platfarm_data to include/linux/platform_data/atmel.h
arm: at91: drop machine defconfig
ARM: OMAP: Remove NEED_MACH_GPIO_H
ARM: OMAP: Remove unnecessary mach and plat includes
...
