Make omap_mpuio_alloc_gc() __devinit as omap_gpio_chip_init()
is __devinit. Otherwise we get:
WARNING: vmlinux.o(.devinit.text+0xa10): Section mismatch in reference
from the function omap_gpio_chip_init() to the function .init.text:omap_mpuio_alloc_gc()
The function __devinit omap_gpio_chip_init() references
a function __init omap_mpuio_alloc_gc().
If omap_mpuio_alloc_gc is only used by omap_gpio_chip_init then
annotate omap_mpuio_alloc_gc with a matching annotation.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
These two functions are used in drivers that can be
modules, so they need to be exported.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alan Ott <alan@signal11.us>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
NCT6775F and NCT6776F have their own set of registers for FAN_STOP_TIME. The
correct registers were used to read FAN_STOP_TIME, but writes used the wrong
registers. Fix it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org # 3.0+
Acked-by: Jean Delvare <khali@linux-fr.org>
If we fail to locate a requested regulator return -EPROBE_DEFER. If drivers
pass this error code through to their caller (which they really should)
then this will ensure that the probe is retried later when further devices
become available. In the unusual case where a driver doesn't want this
it can override the default behaviour.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the variable length array in the RPCSEC_GSS crypto code with
a fixed length one. The size should be bounded by the variable
GSS_KRB5_MAX_BLOCKSIZE, so use that.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The present _get_value routine returns the contents of the GPIO Monitor Pin
Status Register(GPMR) starting from the bit whose value is requested to BIT 0
(irrelevant bits are replace by 0).
For e.g. if we request the value of GPIO 6 in the earlier implementation the
value returned is:
BIT6 followed by 6 0's
whereas it should just return BIT6.
This patch addresses the same.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com>
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Update gpio.txt based on recent discussions regarding interaction with the
pinctrl subsystem.
Previously, gpio_request() was described as explicitly not performing any
required mux setup operations etc.
Now, gpio_request() is explicitly as explicitly performing any required mux
setup operations where possible. In the case it isn't, platform code is
required to have set up any required muxing or other configuration prior to
gpio_request() being called, in order to maintain the same semantics.
This is achieved by gpiolib drivers calling e.g. pinctrl_request_gpio() in
their .request() operation.
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: linux-doc@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The chip offers the function to detect the current state of output of the GPO
P3 pins. Useful for reading GPIO output state in Linux' GPIO API, e.g. via
sysfs.
Please note that this only reads back the currently programmed output state,
not the actual electrical level in terms of a GPI function. Finally, GPO3 is
still just an output.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add missing mask to pin bit selection in gpio-lpc32xx.c
(#define GPIO3_PIN_IN_SEL)
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fixes:
WARNING: drivers/tty/serial/built-in.o(.data+0x30): Section mismatch in reference from the variable vt8500_platform_driver to the function .init.text:vt8500_serial_probe()
The variable vt8500_platform_driver references
the function __init vt8500_serial_probe()
And mark the remove pointer while we are here.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function could fail to queue the upcall if rpc.idmapd is not running,
causing a warning message to be printed. Instead, I want to check the
return value and revoke the key if the upcall can't be run.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Now that the nfs4_cb_match_client() function is static, gcc notices that
it is only used when CONFIG_NFS_V4_1 is enabled.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
__ffs() can tell us which is the SEGMENT_SHIFT value
to be used. This will prevent problems when users are
too fast and don't pay attention to the need of fixing
the Shift after changing TRBS_PER_SEGMENT.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The latest released errata for USB2.0 ECN LPM adds new fields to USB2.0
extension descriptor, defines two BESL values for device: baseline BESL
and deep BESL. Baseline BESL value communicates a nominal power savings
design point and the deep BESL value communicates a significant power
savings design point.
If device indicates BESL value, driver will use a value count in both
host BESL and device BESL. Use baseline BESL value as default.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Tested-by: Jason Fan <jcfan@qca.qualcomm.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
I notice that the commit bbddff makes percpu allocator can work on UP,
So we don't need the magic way for UP.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
While both level- and edge-triggered GPIOs are capable of generating
interrupts, only edge-triggered GPIOs are capable of generating a
module-level wakeup to the PRCM (c.f. 34xx NDA TRM section 25.5.3.2.)
In order to ensure that devices using level-triggered GPIOs as
interrupts can also cause wakeups (e.g. from idle), this patch enables
edge-triggering for wakeup-enabled, level-triggered GPIOs when a GPIO
bank is runtime-suspended (which also happens during idle.)
This fixes a problem found in GPMC-connected network cards with GPIO
interrupts (e.g. smsc911x on Zoom3, Overo, ...) where network booting
with NFSroot was very slow since the GPIO IRQs used by the NIC were
not generating PRCM wakeups, and thus not waking the system from idle.
NOTE: until v3.3, this boot-time problem was somewhat masked because
the UART init prevented WFI during boot until the full serial driver
was available. Preventing WFI allowed regular GPIO interrupts to fire
and this problem was not seen. After the UART runtime PM cleanups, we
no longer avoid WFI during boot, so GPIO IRQs that were not causing
wakeups resulted in very slow IRQ response times.
Tested on platforms using level-triggered GPIOs for network IRQs using
the SMSC911x NIC: 3530/Overo and 3630/Zoom3.
Reported-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This resolves the conflict with drivers/usb/host/ehci-fsl.h that
happened with changes in Linus's and this branch at the same time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
num_sifr could go negative since acpi_pcc_get_sqty() returns -EINVAL
on error. Then it could bypass the sanity check (num_sifr > 255).
The subsequent call to kzalloc() would allocate a small buffer, leading
to a memory corruption.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Add an ethernet SPI chip in the OMAP4 SDP/Blaze board DTS file.
Add a fixed regulator node controlled by a GPIO line to supply
the ethernet chip.
Based on original code from Rajendra.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Add the 4 McSPI controller nodes present in an OMAP4 device.
Remove SPI static device initialisation if DT is populated.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
We have several reports which says acer-wmi is loaded on ideapads
and register rfkill for wifi which can not be unblocked.
Since ideapad-laptop also register rfkill for wifi and it works
reliably, it will be fine acer-wmi is not going to register rfkill
for wifi once VPC2004 is found.
Also put IBM0068/LEN0068 in the list. Though thinkpad_acpi has no
wifi rfkill capability, there are reports which says acer-wmi also
block wireless on Thinkpad E520/E420.
Signed-off-by: Ike Panhc <ike.pan@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This patch adds support for some of the devices within a wide variety
of Fujitsu Tablet Computers, both convertibles and slates. Primarily
it allows for the automatic detection of the tablet/notebook mode for
convertible tablet pc's, and orientation for docked slates. It also
adds support for the application panel buttons usually found next to
the tablet screen, and docking station detection for slates.
Signed-off-by: Robert Gerlach <khnz@gmx.de>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This mainly reverts the commit that was adding the i2c static init.
Since the i2c and twl nodes are now present, there is no need
for the static initialization anymore.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Added the vmaster hook for controlling EAPD dynamically to Conexant
auto-parser. When the Master is muted, EAPDs are turned off as well.
This will fix the missing mute-LED control on some machines in
addition to the more power-saving in the auto-parser mode.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've had ugly static handling of the mute-LED with a powersave hook
for ALC269 HP laptops just like done in patch_sigmatel.c. This is now
rewritten with the new vmaster hook and a fixup code.
For that, the new fixup action, ALC_FIXUP_ACT_BUILD, is introduced.
It's called after build_controls is called. The reason of this new
action is that vmaster hook must be added at this stage (not in init
or probe).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The mute-LED is controlled in patch_sigmatel.c by (ab-)using the
powersave hook. This can be now rewritten with the vmaster hook
instead, which is much simpler and can work even without
CONFIG_SND_HDA_POWER_SAVE kconfig.
A drawback is that the mute-LED corresponds _only_ to the Master mixer
switch instead of checking the whole DACs. But usually this shouldn't
be a big problem as PA enables the mixer elements accordingly.
Also, this patch changes the code to create vmaster always even on
STAC9200 and STAC925x. The former "Master" on these chips are renamed
as "PCM" now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The McBSP driver stack has been moved, and rewritten resulting a single
driver - selected by CONFIG_SND_OMAP_SOC_MCBSP. There is no longer need to
have CONFIG_OMAP_MCBSP anymore.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonoie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
The McBSP driver stack has been moved to ASoC. The CONFIG_OMAP_MCBSP will
be removed since the CONFIG_SND_OMAP_SOC_MCBSP will trigger to build the
McBSP (audio) drivers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
We are setting SNDRV_PCM_HW_PARAM_BUFFER_SIZE based on
SNDRV_PCM_HW_PARAM_CHANNELS, not vice versa. This bug didn't
have much impact because the rules are evaluated multiple times
by the core, and intended value got set eventually.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Remove the no longer valid check for McBSP1 regarding to signal mux
selection (on OMAP4 McBSP4 has 6 pin setup).
Only clear the srgr2, pcr0 register configuration if the requested clock
configuration will actually going to touch it. In this way we can avoid
issues if the CLKR/FSR mux has been configured after the clock selection.
We are going to check for the valid McBSP port in the
omap_mcbsp_6pin_src_mux() function based on the validity of the mux_signal
callback (which is only valid for ports having 6 pin setup).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Use single function for the CLKR/FSR mux configuration.
OMAP2/3 has 6 pin configuration on McBSP1 instance, while on OMAP4
McBSP4 instance have the 6 pin configuration so the omap2_mcbsp1_mux_* is
not correct name for all support OMAP versions
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
On OMAP2/3 McBSP1 port has 6 pin setup, while on OMAP4 the port is McBSP4.
Implement the CLKR/FSR clock mux selection for OMAP4, and make sure that
we add the correct callback for the correct port across supported OMAP
versions.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
On OMAP4 we have one interrupt line per McBSP port.
At probe time tx, and rx irq value will be -ENXIO,
and only the tx irq will get corrected.
In omap_mcbsp_request if the rx_irq is not 0 we proceed,
and try to request the interrupt, which will fail on
OMAP4 (rx_irq == -6).
To avoid this error, clear the rx_irq at probe time
on OMAP4.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
If external source for the CLKS signal selection kept after the port is no
longer in use the system might refuse to go suspend.
There is also a chance that the external clock is not running when next
time the McBSP port is started which can result errors when we try to
access McBSP registers.
Reset the CLKS source back to PRCM source unconditionally.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Configure the WAKEUPEN register at the same time we configure the rest of
the McBSP registers.
In case of OMAP3+, if the sysclock has been reconfigured we are going to
disable McBSP for the duration of the clock change, which will reset the
McBSP registers. The WAKEUPEN register need to be configured later, so
the changes will be effective during runtime.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicrocom>
Signed-off-by: Liam Girdwood <lrg@ti.com>
