Conflicts:
drivers/net/ethernet/atheros/atlx/atl1.c
drivers/net/ethernet/atheros/atlx/atl1.h
Resolved a conflict between a DMA error bug fix and NAPI
support changes in the atl1 driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds FDB bridge ops to the macvlan device passthru mode.
Additionally a flags field was added and a NOPROMISC bit to
allow users to use passthru mode without the driver calling
dev_set_promiscuity(). The flags field is a u16 placed in a
4 byte hole (consuming 2 bytes) of the macvlan_dev struct.
We want to do this so that the macvlan driver or stack
above the macvlan driver does not have to process every
packet. For the use case where we know all the MAC addresses
of the endstations above us this works well.
This patch is a result of Roopa Prabhu's work. Follow up
patches are needed for VEPA and VEB macvlan modes.
v2: Change from distinct nopromisc mode to a flags field to
configure this. This avoids the tendency to add a new
mode every time we need some slightly different behavior.
v3: fix error in dev_set_promiscuity and add change and get
link attributes for flags.
CC: Roopa Prabhu <roprabhu@cisco.com>
CC: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UTA table was being set to the functional equivalent of promiscuous
mode. This was resulting in traffic from the virtual function being
flooded onto the wire and the PF device. This resulted in additional
overhead for VF traffic sent to the network and in the case of traffic
sent to the PF or another VF resulted in unwanted packets on the wire.
This was actually not the intended behavior. Now that we can program
the embedded switch correctly we can remove this snippit of code. Users
who want to support this should configure the FDB correctly using the
FDB ops.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows RAR table updates while in promiscuous. With
SR-IOV enabled it is valuable to allow the RAR table to
be updated even when in promisc mode to configure forwarding
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is useful to be able to monitor for FDB events in user space.
This patch adds support to generate netlink events when a change
is made to a device supporting the FDB ops.
This brings embedded switches inline with the SW net/bridge which
triggers events on FDB updates as well.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a generic dump routine drivers can call. It
should be sufficient to handle any bridging model that
uses the unicast address list. This should be most SR-IOV
enabled NICs.
v2: return error on nlmsg_put and use -EMSGSIZE instead
of -ENOMEM this is inline other usages
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a dev_uc_add_excl() and dev_mc_add_excl() calls
similar to the original dev_{uc|mc}_add() except it sets
the global bit and returns -EEXIST for duplicat entires.
This is useful for drivers that support SR-IOV, macvlan
devices and any other devices that need to manage the
unicast and multicast lists.
v2: fix typo UNICAST should be MULTICAST in dev_mc_add_excl()
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds two new flags NTF_MASTER and NTF_SELF that can
now be used to specify where PF_BRIDGE netlink commands should
be sent. NTF_MASTER sends the commands to the 'dev->master'
device for parsing. Typically this will be the linux net/bridge,
or open-vswitch devices. Also without any flags set the command
will be handled by the master device as well so that current user
space tools continue to work as expected.
The NTF_SELF flag will push the PF_BRIDGE commands to the
device. In the basic example below the commands are then parsed
and programmed in the embedded bridge.
Note if both NTF_SELF and NTF_MASTER bits are set then the
command will be sent to both 'dev->master' and 'dev' this allows
user space to easily keep the embedded bridge and software bridge
in sync.
There is a slight complication in the case with both flags set
when an error occurs. To resolve this the rtnl handler clears
the NTF_ flag in the netlink ack to indicate which sets completed
successfully. The add/del handlers will abort as soon as any
error occurs.
To support this new net device ops were added to call into
the device and the existing bridging code was refactored
to use these. There should be no required changes in user space
to support the current bridge behavior.
A basic setup with a SR-IOV enabled NIC looks like this,
veth0 veth2
| |
------------
| bridge0 | <---- software bridging
------------
/
/
ethx.y ethx
VF PF
\ \ <---- propagate FDB entries to HW
\ \
--------------------
| Embedded Bridge | <---- hardware offloaded switching
--------------------
In this case the embedded bridge must be managed to allow 'veth0'
to communicate with 'ethx.y' correctly. At present drivers managing
the embedded bridge either send frames onto the network which
then get dropped by the switch OR the embedded bridge will flood
these frames. With this patch we have a mechanism to manage the
embedded bridge correctly from user space. This example is specific
to SR-IOV but replacing the VF with another PF or dropping this
into the DSA framework generates similar management issues.
Examples session using the 'br'[1] tool to add, dump and then
delete a mac address with a new "embedded" option and enabled
ixgbe driver:
# br fdb add 22:35:19:ac:60:59 dev eth3
# br fdb
port mac addr flags
veth0 22:35:19:ac:60:58 static
veth0 9a:5f:81:f7:f6:ec local
eth3 00:1b:21:55:23:59 local
eth3 22:35:19:ac:60:59 static
veth0 22:35:19:ac:60:57 static
#br fdb add 22:35:19:ac:60:59 embedded dev eth3
#br fdb
port mac addr flags
veth0 22:35:19:ac:60:58 static
veth0 9a:5f:81:f7:f6:ec local
eth3 00:1b:21:55:23:59 local
eth3 22:35:19:ac:60:59 static
veth0 22:35:19:ac:60:57 static
eth3 22:35:19:ac:60:59 local embedded
#br fdb del 22:35:19:ac:60:59 embedded dev eth3
I added a couple lines to 'br' to set the flags correctly is all. It
is my opinion that the merit of this patch is now embedded and SW
bridges can both be modeled correctly in user space using very nearly
the same message passing.
[1] 'br' tool was published as an RFC here and will be renamed 'bridge'
http://patchwork.ozlabs.org/patch/117664/
Thanks to Jamal Hadi Salim, Stephen Hemminger and Ben Hutchings for
valuable feedback, suggestions, and review.
v2: fixed api descriptions and error case with both NTF_SELF and
NTF_MASTER set plus updated patch description.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To prevent interrupts lost they should be dropped only if
they are scheduled via napi interfaces. In other case, there is
exists situation when napi handler process TX interrupt, stay in
RX processing and in that moment any other interrupt received.
Then before this patch TX bit in ISR will be cleaned, napi
schedule will not occur in case of currently processing event and
TX interrupt definitely will be lost.
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the rx/tx handled inside napi handler, the cycle is
not needed now, because only the rx/tx need such kind of
processing.
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unfortunately it is not clear from code is usage of
IMR register possible or not. So, to prevent possible
side-effects of reading this register i prefer store
interrupts enable flag separately.
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function should be used later to set/remove proper
bits in imr to disable only rx ints.
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like direct writes to IMR register is not good idea,
because there are exist functions to make this work.
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the tx ints processing same as rx ones via napi.
The idea got from e1000. The interrupt disabling is
still not fine grained.
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is first step, here there is no fine interrupt
disabling which cause TX/ERR interrupts stalling when
RX scheduled ints processed.
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove rx from unlikely optimization in case of rx is very
likely thing for network card. This also reduce code a bit.
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sending general queries was implemented as an optimisation to speed
up convergence on start-up. In order to prevent interference with
multicast routers a zero source address has to be used.
Unfortunately these packets appear to cause some multicast-aware
switches to misbehave, e.g., by disrupting multicast packets to us.
Since the multicast snooping feature still functions without sending
our own queries, this patch will change the default to not send
queries.
For those that need queries in order to speed up convergence on start-up,
a toggle is provided to restore the previous behaviour.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it stands when we discover that a real querier (one that queries
with a non-zero source address) we stop querying. However, even
after said querier has fallen off the edge of the earth, we will
never restart querying (unless the bridge itself is restarted).
This patch fixes this by kicking our own querier into gear when
the timer for other queriers expire.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the helper br_multicast_start_querier so that
the code which starts the queriers in br_multicast_toggle can
be reused elsewhere.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of "unsigned int" is preferred to bare "unsigned" in net tree.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix checkpatch errors of the following type:
* ERROR: "foo * bar" should be "foo *bar"
* ERROR: "(foo*)" should be "(foo *)"
Signed-off-by: Daniel Baluta <dbaluta@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mixer units from the firmware are corrupt, and even where they
are valid they presents mono controls as L and R channels of
stereo.
Signed-off-by: Mark Hills <mark@pogo.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some interfaces reference endpoints which do not exists. To
accomodate these, do not fail completely, but skip over them.
This allows the Electrix Ebox-44 with earlier firmware to be
detected and used for audio.
Signed-off-by: Mark Hills <mark@pogo.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There's no need to implement set_voltage() as there is only a very small
range of selectors for the regulators in the WM8994 and the voltages are
not expected to vary frequently at runtime.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As reported by David Gibson, current code handles PAGE_SIZE != 4k
completely wrong which can lead to guest memory corruption errors:
- page_to_balloon_pfn is wrong: e.g. on system with 64K page size
it gives the same pfn value for 16 different pages.
- we also need to convert back to linux pfns when we free.
- for each linux page we need to tell host about multiple balloon
pages, but code only adds one pfn to the array.
This patch fixes all that, tested with a 64k ppc64 kernel.
Reported-by: David Gibson <david@gibson.dropbear.id.au>
Tested-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Although virtio config space fields are usually in guest-native endian,
the spec for the virtio balloon device explicitly states that both fields
in its config space are little-endian.
However, the current virtio_balloon driver does not have a suitable endian
swap for the 'num_pages' field, although it does have one for the 'actual'
field. This patch corrects the bug, adding sparse annotation while we're
at it.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As hypervior does not have the knowledge of guest network configuration, it's
better to ask guest to send gratuitous packets when needed.
This patch implements VIRTIO_NET_F_GUEST_ANNOUNCE feature: hypervisor would
notice the guest when it thinks it's time for guest to announce the link
presnece. Guest tests VIRTIO_NET_S_ANNOUNCE bit during config change interrupt
and woule send gratuitous packets through netif_notify_peers() and ack the
notification through ctrl vq.
We need to make sure the atomicy of read and ack in guest otherwise we may ack
more times than being notified. This is done through handling the whole config
change interrupt in an non-reentrant workqueue.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the code for getting an number from a
userspace buffer by a simple call to kstroul_from_user.
This makes it easier to read and less error prone.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull perf tooling fixes from Arnaldo Carvalho de Melo:
. Properly handle ~/.debug, the build id cache, when it is a symlink,
fix from Chanho Park
. Fixes for the parser generation process, from Jiri Olsa and Namhyung Kim
. Fix build when NO_GTK2 is specified, From Stephane Eranian
. When a machine is not found, bump the relevant error stat but return
0, so that we correctly move to the next perf event. Fix from Jiri Olsa
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that we have OPP layer, and OMAP CPUfreq driver is using it, we no
longer need/use the clock framework code for filling up CPUfreq
tables. Remove it.
Removing this code also eliminates build errors when CPU_FREQ_TABLE
support is not enabled.
Thanks to Russell King for pointing out the parts I missed under
plat-omap in the original version and also pointing out the build
errors when CPUFREQ_TABLE support was not enabled.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
These were incorrectly introduced and can cause problems for of_irq_init.
The correct way to define a root controller is no interrupt-parent set at
all or the interrupt-parent is set to the root controller itself when
inherited from a parent node.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Tested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
From David Brown:
"Here are some fixes for msm that fix problems caused by the latest
ARM code. The ones from Daniel remove unneeded fixups that now
cause compilation failures. Mine fix section mismatches, that were
incompletely fixed earlier."
* 'msm-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
ARM: msm: Fix section mismatches in proc_comm.c
video: msm: Fix section mismatches in mddi.c
arm: msm: trout: fix compile failure
arm: msm: halibut: remove unneeded fixup
We originally changed iscsi to allocate its own buffers just as an
intermediate step to clean up some core buffer allocation mechanisms. Now
we can put it back.
Also had to change allocate_iovecs to use data_length instead of
t_data_nents because iovecs are now allocated before the data buffer, thus
t_data_nents is not yet initialized.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
It appears iscsi is the only one to call this in its cmd submit path, but
it appears to be applicable to all fabrics, and should always be called.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Rename iscsit_build_pdu_and_seq_list to iscsit_do_build_pdu_and_seq_lists
Rename iscsit_do_build_list to iscsit_build_pdu_and_seq_lists
Move code from iscsit_decide_list_to_build into _seq_pdu_list.c, seems
a better fit.
Also update some comments in pdu/seq code for correctness and whitespace.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Redundant, just use iscsi_cmd->se_cmd.data_length once se_cmd is
initialized, or hdr->data_length before then.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
if we can get calls to init_se_cmd, get_sess_cmd, lookup_cmd_lun,
core_alua_check_nonop_delay, and handle_cdb_direct next to each other,
then we can just call target_submit_cmd. This is a step towards that
goal.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Trying to move a bunch of stuff around so iscsi can use target_submit_cmd
someday, and so stuff needs to be in that function directly instead of
hidden, so it can be reordered etc.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch renames a horribly misnamed function that no longer allocate
tasks to something more descriptive for it's modern use in target core.
(nab: Fix up ib_srpt to use this as well ahead of a target_submit_cmd
conversion)
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch includes the handful of squashed patches for target/iscsi from
Andy's original series into lio-core/master code:
*) Make iscsit_add_reject static
*) Remove unused data_offset_end from iscsi_datain_req
*) Remove "#if 0" stubs
*) Rename iscsi_datain_req to cmd_datain_node
*) Cleanups for built_r2ts_for_cmd()
*) Cleanups for Cleanup build_sendtargets_response()
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Immediate queue:
Consolidate down to one switch statement by moving send_tx_data and stuff
from second switch into the first switch, or the functions the first switch
calls.
Response queue:
Do not lock istate_lock except directly around i_state modifications.
Put entire ISTATE_SEND_DATAIN path within first switch statement, in prep
for further refactoring.
All other cases set use_misc = 1 and will not be using sendpage, so just
use send_tx_data for these and set use_misc param to 1.
map_sg, sent_status, use_misc, and se_cmd vars no longer needed.
Then put immediate and response handling in separate functions in order
to get iscsi_target_tx_thread down to where it fits on a page.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When processing immediate queue, we're switching on a local variable
so it's not necessary to lock around it. However, we are modifying
cmd->i_state in two spots, so lock around those parts only.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
