This patch eliminates parameter "buf1" from function gfs2_setbit.
This is possible because it was always passed in as bi->bi_bh->b_data.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch consolidates the case logic for checking whether a device supports
WoL into a single place. Previously ethtool and probe used similar logic that
was copied and maintained separately. This patch encapsulates the core logic
into a function so that a user only has to update one place.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During igb_reset(), we initiate a hardware reset which will clear our
flow control settings. For auto-negotiation, we re-negotiate them when
linking up again, but we need to force them off properly for the forced
speed case.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously, a workaround was added to address a hardware bug in the
PCIm2PCI arbiter where a write by the driver of the Transmit/Receive
Descriptor Tail register could happen concurrently with a write of any
MAC CSR register by the Manageability Engine (ME) which could cause the
Tail register to have an incorrect value. The arbiter is supposed to
prevent the concurrent writes but there is a bug that can cause the Host
(driver) access to be acknowledged later than it should.
After further investigation, it was discovered that a driver write access
of any MAC CSR register after being idle for some time can be lost when
ME is accessing a MAC CSR register. When this happens, no further target
access is claimed by the MAC which could hang the system.
The workaround to check bit 24 in the FWSM register (set only when ME is
accessing a MAC CSR register) and delay for a limited amount of time until
it is cleared is now done for all driver writes of MAC CSR registers on
82579 with ME enabled. In the rare case when the driver is writing the
Tail register and ME is accessing any MAC CSR register for a duration
longer than the maximum delay, write the register and verify it has the
correct value before continuing, otherwise reset the device.
This patch also moves some pre-existing macros from the hardware-specific
header file to the more appropriate generic driver header file.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In K1 mode (a MAC/PHY interconnect power mode), the 82579 device shuts down
the Phase Lock Loop (PLL) of the interconnect to save power. When the PLL
starts working, the 82579 device may start to transfer the packet through
the interconnect before it is fully functional causing packet drops. This
workaround disables shutting down the PLL in K1 mode for 1G link speed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
80003ES2LAN has an errata such that far-end loopback may be activated by
bit errors producing a reserved symbol. In order to disable far-end
loopback quickly enough, disable it immediately following a reset.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This fixes:
WARNING: arch/arm/mach-davinci/built-in.o(.text+0x2d84): Section mismatch in reference from the function da850_evm_ui_expander_setup() to the (unknown reference) .init.data:(unknown)
The function da850_evm_ui_expander_setup() references
the (unknown reference) __initdata (unknown).
This is often because da850_evm_ui_expander_setup lacks a __initdata
annotation or the annotation of (unknown) is wrong.
Note this is a real issue because if the tca6416 driver only binds when
the init sections are already discarded da850_evm_ui_expander_setup is
called when da850_evm_devices might already be overwritten.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Direct keys usage may not start from KP_DKIN0, add a msk option
to configure the specifics for platforms that can skip some keys.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
KPDK_DK only indicates the pin level of direct key.
So it is related to board, and low level may be active which
indicates that a key is pressed.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
When direcct_key_num is 0, the mask should be 0.
When direcct_key_num is 1, the mask should be 0b1.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
When the keypad is used as wake up source, the clock can not
be disabled. Or it can not detect key pressing.
If the keypad is used as wake up source, when resume back,
do not enable the clock and configure it again because the
register content is retained.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Some boards such as the Intel D2700MUD allow you to have over 4GB of RAM.
The GTT on the PVR based devices is 32bit however. Hugh Dickins points out
that we should therefore be setting the mapping gfp mask.
This is not the whole fix for the problem. Some further shmem patches will
be needed to deal with the corner cases.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This provides the needed callback hooks to add hotplug display support to
the GMA36x0 devices.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In particular clean up the errata handling and correct the crtc masks. We do
this a bit differently using our device abstraction for neatness.
This doesn't address the ACPI opregion and hotplug plumbing, nor the IRQ related
changes that will need. It touches on backlight init but the full backlight
support is not in this change set.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The problem in console mode is lack of linear memory. We can solve that by
dropping to 16bpp. The mode setting X server will allocate its own GEM
framebuffer in 32bpp and all will be well.
We could just do 16bpp anyway but that would be a regression on the lower
modes as many distributions don't yet ship the generic mode setting KMS
drivers.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Introduce a panel presence check for Cedartrail. Non netbook devices don't
necessarily have a panel attached.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pull in various i915 bits that we will need to begin tackling the LVDS detect
and ACPI events. We try and drift towards the i915 version of the code with
the long term goal that at least some of it can one day be unified.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We don't want them uncached, combining will do nicely and fixes the performance
problem with the generic modesetting X server.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need to pull more stuff from the VBT in order to configure the clocking
correctly in all cases. Add the relevant bits from the other CDV driver work.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This was reported a long time ago (and I apologize to whoever it was that
reported it as I've lost the original report).
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch (as1548) fixes a recently-introduced incompatibility
between the UDC core and the dummy-hcd driver. Commit
8ae8090c82 (usb: gadget: udc-core: fix
asymmetric calls in remove_driver) moved the usb_gadget_udc_stop()
call in usb_gadget_remove_driver() below the usb_gadget_disconnect()
call.
As a result, usb_gadget_disconnect() gets called at a time when the
gadget driver believes it has been unbound but dummy-hcd believes
it has not. A nasty error ensues when dummy-hcd calls the gadget
driver's disconnect method a second time.
To fix the problem, this patch moves the gadget driver's unbind
notification after the usb_gadget_disconnect() call. Now nothing
happens between the two unbind notifications, so nothing goes wrong.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 6d258a4 (usb: gadget: udc-core: stop UDC on device-initiated
disconnect) introduced another case of asymmetric calls when issuing
a device-initiated disconnect. Fix it.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
EDID vendor IDs are always 3 characters long (4 with the terminating
0). It doesn't make any sense to have a (possibly 8-byte) pointer
to the ID string in the quirk structure.
Signed-off-by: Ian Pilcher <arequipeno@gmail.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Requiring the first byte of the EDID base block header to be 0 means we
don't fix up as many transfer errors as we could. Instead have the
callers specify whether it's meant to be block 0 or not, and
conditionally run header fixup based on that.
Bugzilla: https://bugzilla.redhat.com/812890
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From Daniel Vetter
- VGA load-detect fix. This bug seems to be as old as the load-detect code
(2.6.30), but needs stupid userspace (upowerd trying to detect
connectors on dpms-off outputs) to actually kill the machine. And
obviously a machine without VGA-hotplug, otherwise we don't do load
detect.
- 2 interger overflow fixes for unpriviledged ioctls from Xi Wang.
- Fix SDVO regression for low-res (pixelclock < 100MHz) digital outputs,
introduce in 2.6.36.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: handle input/output sdvo timings separately in mode_set
drm/i915: fix integer overflow in i915_gem_do_execbuffer()
drm/i915: fix integer overflow in i915_gem_execbuffer2()
drm/i915: fixup load-detect on enabled, but not active pipe
From Inki Dae:
this patch set fixes gem allocation and mapping issue between user space and
physical memory region.
* 'exynos-drm-fixes' of git://git.infradead.org/users/kmpark/linux-2.6-samsung:
drm/exynos: added missed vm area region mapping type.
drm/exynos: fixed exynos_drm_gem_map_pages bug.
drm/exynos: fixed duplicatd memory allocation bug.
Annotation improvements:
Now the default annotate browser uses a much more compact format, implementing
suggestions made made by several people, notably Linus.
Here is part of the new __list_del_entry() annotation:
__list_del_entry
8.47 │ push %rbp
8.47 │ mov (%rdi),%rdx
20.34 │ mov $0xdead000000100100,%rcx
3.39 │ mov 0x8(%rdi),%rax
0.00 │ mov %rsp,%rbp
1.69 │ cmp %rcx,%rdx
0.00 │ je 43
1.69 │ mov $0xdead000000200200,%rcx
3.39 │ cmp %rcx,%rax
0.00 │ je a3
5.08 │ mov (%rax),%r8
18.64 │ cmp %r8,%rdi
0.00 │ jne 84
1.69 │ mov 0x8(%rdx),%r8
25.42 │ cmp %r8,%rdi
0.00 │ jne 65
1.69 │ mov %rax,0x8(%rdx)
0.00 │ mov %rdx,(%rax)
0.00 │ leaveq
0.00 │ retq
0.00 │ 43: mov %rdx,%r8
0.00 │ mov %rdi,%rcx
0.00 │ mov $0xffffffff817cd6a8,%rdx
0.00 │ mov $0x31,%esi
0.00 │ mov $0xffffffff817cd6e0,%rdi
0.00 │ xor %eax,%eax
0.00 │ callq ffffffff8104eab0 <warn_slowpath_fmt>
0.00 │ leaveq
0.00 │ retq
0.00 │ 65: mov %rdi,%rcx
0.00 │ mov $0xffffffff817cd780,%rdx
0.00 │ mov $0x3a,%esi
0.00 │ mov $0xffffffff817cd6e0,%rdi
0.00 │ xor %eax,%eax
0.00 │ callq ffffffff8104eab0 <warn_slowpath_fmt>
0.00 │ leaveq
0.00 │ retq
The infrastructure is there to provide formatters for any instruction,
like the one I'll do for call functions to elide the address.
Further fixes on top of the first iteration:
- Sometimes a jump points to an offset with no instructions, make the
mark jump targets function handle that, for now just ignoring such
jump targets, more investigation is needed to figure out how to cope
with that.
- Handle jump targets that are outside the function, for now just don't
try to draw the connector arrow, right thing seems to be to mark this
jump with a -> (right arrow) and handle it like a callq.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On the htc mbox layer, it will assign each endpoint (AC) with a
different Tx-packet-drop threshold, so lower priority AC is more
likely to drop packets and the cookies become more available to higher
priority AC.
On the htc pipe layer, assign the tx packet drop threshold as well, it
will let AC to drop packets when cookies below the tx packet drop
threshold.
Signed-off-by: Kevin Fang <kevin.fang@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When a STA sends huge BK QoS data frame first and then sends BE/VI/VO
QoS data frame, the corresponding throughput becomes much lower than
that without sends BK QoS data frame before.
The root cause is that when station send BK stream, the tx credits of
BK stream don't return back to higher priority QoS stream such as BE,
VI, and VO stream. This patch will handle BK stream properly, when
there is higher priority QoS stream, it will seek tx credits from BK
stream properly.
Signed-off-by: Kevin Fang <kevin.fang@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
bss filter is configured to allow the frames from all the bss other
than the currenly connected one, this is done when a scan is requested
in connected state. There is no reason to filter out the currently
connected bss, configure the filter to allow all the bss. This would
fix the reporting of stale rssi of the current bss while scanning.
Reported-by: Naveen singh <navesing@qca.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use min_t()/max_t() macros, reformat two comments, use !!test_bit() to
match !!sock_flag()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Micron MT9M111 camera chip needs its output enable to be
activated in order to work. The bootloader is not required to
activate it, so do it in machine code.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
The pcm990 baseboard for the pcm027 module used to setup a static
mapping for accessing the CPLD. It became illegal to call iotable_init
that late. The pcm027 support is broken since then. This patch
switches the cpld support to ioremap and removes all references to
previous static mappings.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
All parameter descriptions in /proc/sys/net/core/* now is separated
two places. So, merge them into Documentation/sysctl/net.txt.
Signed-off-by: Shan Wei <davidshan@tencent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
logical speed returned by link_status_query needs to be multiplied by 10.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This has been used by me and others for ages, let's stop calling it
experimental.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As none of the callers of bond_update_speed_duplex (need to) check its
return value, there is little point in it returning anything.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
