[ Upstream commit 0422253ac1919fea8292381c85f11a9decff1bb1 ]
The switch from 1/10 to 1/40 clock ratio must happen when exceeding the
340 MHz rate limit of HDMI 1.4, i.e. when entering the HDMI 2.0 domain,
and not before.
Therefore, use the correct comparison operator '>' instead of '>=' when
checking the max rate. While at it, introduce a define for this rate
limit constant.
Fixes: 553be2830c ("phy: rockchip: Add Samsung HDMI/eDP Combo PHY driver")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20250318-phy-sam-hdptx-bpc-v6-3-8cb1678e7663@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9475055b11c0c70979bd1667a76b2ebae638eb7 ]
When using HDMI PLL frequency division coefficient at 50.25MHz
that is calculated by rk_hdptx_phy_clk_pll_calc(), it fails to
get PHY LANE lock. Although the calculated values are within the
allowable range of PHY PLL configuration.
In order to fix the PHY LANE lock error and provide the expected
50.25MHz output, manually compute the required PHY PLL frequency
division coefficient and add it to ropll_tmds_cfg configuration
table.
Signed-off-by: Algea Cao <algea.cao@rock-chips.com>
Reviewed-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250427095124.3354439-1-algea.cao@rock-chips.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 969a38be437b68dc9e12e3c3f08911c9f9c8be73 ]
According documentation of phy_configure_opts_dp, at the configure
stage, link rates should only be verify/configure when set_rate
flag is set, the same applies to lanes and voltage.
So do it as the documentation says.
Because voltage setting depends on the lanes, link rates set
previously, so record the link rates and lanes at it's verify stage.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Link: https://lore.kernel.org/r/20250312080041.524546-1-andyshrk@163.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28dc672a1a877c77b000c896abd8f15afcdc1b0c ]
Function rk_udphy_dp_hpd_event_trigger will set vogrf let it
trigger HPD interrupt to DP by Type-C. This configuration is only
required when the DP work in Alternate Mode, and called by
typec_mux_set. In standard DP mode, such settings will prevent
the DP from receiving HPD interrupts.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Link: https://lore.kernel.org/r/20250302115257.188774-1-andyshrk@163.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f08d1c08563846f9be79a4859e912c8795d690fd ]
The phy needs to know its identity in the system (phy0 or phy1 on rk3588)
for some actions and the driver currently contains code abusing of_alias
for that.
Devicetree aliases are always optional and should not be used for core
device functionality, so instead keep a list of phys on a soc in the
of_device_data and find the phy-id by comparing against the mapped
register-base.
Fixes: c4b09c5620 ("phy: phy-rockchip-samsung-hdptx: Add clock provider support")
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20241206103401.1780416-3-heiko@sntech.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fcf5d353b09b3fc212ab24b89ef23a7a8f7b308e ]
A previous patch ensured that USB Type C connector support is enabled,
but it is still possible to build the phy driver without enabling
CONFIG_USB (host support) or CONFIG_USB_GADGET (device support), and
in that case the common helper functions are unavailable:
aarch64-linux-ld: drivers/phy/rockchip/phy-rockchip-usbdp.o: in function `rk_udphy_probe':
phy-rockchip-usbdp.c:(.text+0xe74): undefined reference to `usb_get_maximum_speed'
Select CONFIG_USB_COMMON directly here, like we do in some other phy
drivers, to make sure this is available even when actual USB support
is disabled or in a loadable module that cannot be reached from a
built-in phy driver.
Fixes: 9c79b77964 ("phy: rockchip: fix CONFIG_TYPEC dependency")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250122065249.1390081-1-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fbcbffbac994aca1264e3c14da96ac9bfd90466e upstream.
Currently, the USB port via combophy on the RK3528/RK3588 SoC is broken.
usb usb8-port1: Cannot enable. Maybe the USB cable is bad?
This is due to the combphy of RK3528/RK3588 SoC has multiple resets, but
only "phy resets" need assert and deassert, "apb resets" don't need.
So change the driver to only match the phy resets, which is also what
the vendor kernel does.
Fixes: 7160820d74 ("phy: rockchip: add naneng combo phy for RK3568")
Cc: FUKAUMI Naoki <naoki@radxa.com>
Cc: Michael Zimmermann <sigmaepsilon92@gmail.com>
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://lore.kernel.org/r/20241122073006.99309-2-amadeus@jmu.edu.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure CONFIG_PHY_ROCKCHIP_SAMSUNG_HDPTX depends on CONFIG_COMMON_CLK to
fix the following link errors when compile testing some random kernel
configurations:
m68k-linux-ld: drivers/phy/rockchip/phy-rockchip-samsung-hdptx.o: in function `rk_hdptx_phy_clk_register':
drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c:1031:(.text+0x470): undefined reference to `__clk_get_name'
m68k-linux-ld: drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c:1036:(.text+0x4ba): undefined reference to `devm_clk_hw_register'
m68k-linux-ld: drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c:1040:(.text+0x4d2): undefined reference to `of_clk_hw_simple_get'
m68k-linux-ld: drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c:1040:(.text+0x4da): undefined reference to `devm_of_clk_add_hw_provider'
Fixes: c4b09c5620 ("phy: phy-rockchip-samsung-hdptx: Add clock provider support")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202409180305.53PXymZn-lkp@intel.com/
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240923-sam-hdptx-link-fix-v1-1-8d10d7456305@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The HDMI PHY PLL can be used as an alternative dclk source to RK3588 SoC
CRU. It provides more accurate clock rates required by VOP2 to improve
existing support for display modes handling, which is known to be
problematic when dealing with non-integer refresh rates, among others.
It is worth noting this only works for HDMI 2.0 or below, e.g. cannot be
used to support HDMI 2.1 4K@120Hz mode.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20240620-rk3588-hdmiphy-clkprov-v2-4-6a2d2164e508@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When a new PHY is created via [devm_]phy_create(), the runtime PM for it
is not enabled unless the parent device (which creates the PHY) has its
own runtime PM already enabled.
Move the call to devm_pm_runtime_enable() before devm_phy_create() to
enable runtime PM at PHY core level.
With this change the ->power_on() and ->power_off() callbacks do not
require explicit runtime PM management anymore, since the PHY core
handles that via phy_pm_runtime_{get,put}_sync() when phy_power_on() and
phy_power_off() are invoked.
Hence drop the now unnecessary calls to pm_runtime_resume_and_get() and
pm_runtime_put() helpers.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20240620-rk3588-hdmiphy-clkprov-v2-2-6a2d2164e508@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Compile testing configurations without REGMAP support enabled results in
a bunch of errors being reported:
../drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c:569:21: error: variable ‘rk_hdptx_phy_regmap_config’ has initializer but incomplete type
569 | static const struct regmap_config rk_hdptx_phy_regmap_config = {
| ^~~~~~~~~~~~~
../drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c:570:10: error: ‘const struct regmap_config’ has no member named ‘reg_bits’
570 | .reg_bits = 32,
| ^~~~~~~~
Note that selecting REGMAP alone is not enough, because of the following
liker error:
phy-rockchip-samsung-hdptx.c:(.text+0x10c): undefined reference to `__devm_regmap_init_mmio_clk'
Instead of the obvious fix to enable REGMAP_MMIO, select MFD_SYSCON,
which implicitly enables REGMAP_MMIO as well. The rationale is that the
driver has been already relying on the syscon functionality.
Moreover, without MFD_SYSCON enabled, the test coverage is reduced,
since the linker might not detect any potential undefined references
following syscon_regmap_lookup_by_phandle() invocation in
rk_hdptx_phy_probe() body. That is because the function would
unconditionally return -ENOTSUP, hence the compiler is free to optimize
out any unreachable code.
Finally ensure PHY_ROCKCHIP_SAMSUNG_HDPTX depends on HAS_IOMEM, as
required by MFD_SYSCON.
Fixes: 553be2830c ("phy: rockchip: Add Samsung HDMI/eDP Combo PHY driver")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20240629-rk-hdptx-compile-test-fix-v1-1-c86675ba8070@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The newly added driver causes a warning about missing dependencies
by selecting CONFIG_TYPEC unconditionally:
WARNING: unmet direct dependencies detected for TYPEC
Depends on [n]: USB_SUPPORT [=n]
Selected by [y]:
- PHY_ROCKCHIP_USBDP [=y] && ARCH_ROCKCHIP [=y] && OF [=y]
WARNING: unmet direct dependencies detected for USB_COMMON
Depends on [n]: USB_SUPPORT [=n]
Selected by [y]:
- EXTCON_RTK_TYPE_C [=y] && EXTCON [=y] && (ARCH_REALTEK [=y] || COMPILE_TEST [=y]) && TYPEC [=y]
Since that is a user-visible option, it should not really be selected
in the first place. Replace the 'select' with a 'depends on' as
we have for similar drivers.
Fixes: 2f70bbddeb ("phy: rockchip: add usbdp combo phy driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240415174241.77982-1-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
>From the RK3588 Technical Reference Manual, Part1,
section 6.19 PCIe3PHY_GRF Register Description:
"rxX_cmn_refclk_mode"
RX common reference clock mode for lane X. This mode should be enabled
only when the far-end and near-end devices are running with a common
reference clock.
The hardware reset value for this field is 0x1 (enabled).
Note that this register field is only available on RK3588, not on RK3568.
The link training either fails or is highly unstable (link state will jump
continuously between L0 and recovery) when this mode is enabled while
using an endpoint running in Separate Reference Clock with No SSC (SRNS)
mode or Separate Reference Clock with SSC (SRIS) mode.
(Which is usually the case when using a real SoC as endpoint, e.g. the
RK3588 PCIe controller can run in both Root Complex and Endpoint mode.)
Add support for the device tree property rockchip,rx-common-refclk-mode,
such that the PCIe PHY can be used in configurations where the Root
Complex and Endpoint are not using a common reference clock.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Link: https://lore.kernel.org/r/20240412125818.17052-3-cassel@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This adds a new USBDP combo PHY with Samsung IP block driver.
The driver get lane mux and mapping info in 2 ways, supporting
DisplayPort alternate mode or parsing from DT. When parsing from DT,
the property "rockchip,dp-lane-mux" provide the DP mux and mapping
info. This is needed when the PHY is not used with TypeC Alt-Mode.
For example if the USB3 interface of the PHY is connected to a USB
Type A connector and the DP interface is connected to a DisplayPort
connector.
When do DP link training, need to set lane number, link rate, swing,
and pre-emphasis via PHY configure interface.
Co-developed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Co-developed-by: Zhang Yubing <yubing.zhang@rock-chips.com>
Signed-off-by: Zhang Yubing <yubing.zhang@rock-chips.com>
Co-developed-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20240408225109.128953-3-sebastian.reichel@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The pcie1l0_sel and pcie1l1_sel bits in PCIESEL_CON configure the
mux for PCIe1L0 and PCIe1L1 to either the PIPE Combo PHYs or the
PCIe3 PHY. Thus this configuration interfers with the data-lanes
configuration done by the PCIe3 PHY.
RK3588 has three Combo PHYs. The first one has a dedicated PCIe
controller and is not affected by this. For the other two Combo
PHYs, there is one mux for each of them.
pcie1l0_sel selects if PCIe 1L0 is muxed to Combo PHY 1 when
bit is set to 0 or to the PCIe3 PHY when bit is set to 1.
pcie1l1_sel selects if PCIe 1L1 is muxed to Combo PHY 2 when
bit is set to 0 or to the PCIe3 PHY when bit is set to 1.
Currently the code always muxes 1L0 and 1L1 to the Combi PHYs
once one of them is being used in PCIe mode. This is obviously
wrong when at least one of the ports should be muxed to the
PCIe3 PHY.
Fix this by introducing Combo PHY identification and then only
setting up the required bit.
Fixes: a03c442772 ("phy: rockchip: Add naneng combo phy support for RK3588")
Reported-by: Michal Tomek <mtdev79b@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240404-rk3588-pcie-bifurcation-fixes-v1-3-9907136eeafd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
So far all RK3588 boards use fully aggregated PCIe. CM3588 is one
of the few boards using this feature and apparently it is broken.
The PHY offers the following mapping options:
port 0 lane 0 - always mapped to controller 0 (4L)
port 0 lane 1 - to controller 0 or 2 (1L0)
port 1 lane 0 - to controller 0 or 1 (2L)
port 1 lane 1 - to controller 0, 1 or 3 (1L1)
The data-lanes DT property maps these as follows:
0 = no controller (unsupported by the HW)
1 = 4L
2 = 2L
3 = 1L0
4 = 1L1
That allows the following configurations with first column being the
mainline data-lane mapping, second column being the downstream name,
third column being PCIE3PHY_GRF_CMN_CON0 and PHP_GRF_PCIESEL register
values and final column being the user visible lane setup:
<1 1 1 1> = AGGREG = [4 0] = x4 (aggregation)
<1 1 2 2> = NANBNB = [0 0] = x2 x2 (no bif.)
<1 3 2 2> = NANBBI = [1 1] = x2 x1x1 (bif. of port 0)
<1 1 2 4> = NABINB = [2 2] = x1x1 x2 (bif. of port 1)
<1 3 2 4> = NABIBI = [3 3] = x1x1 x1x1 (bif. of both ports)
The driver currently does not program PHP_GRF_PCIESEL correctly, which
is fixed by this patch. As a side-effect the new logic is much simpler
than the old logic.
Fixes: 2e9bffc4f7 ("phy: rockchip: Support PCIe v3")
Signed-off-by: Michal Tomek <mtdev79b@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240404-rk3588-pcie-bifurcation-fixes-v1-1-9907136eeafd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit 51a9b2c03d ("phy: rockchip-inno-usb2: Handle ID IRQ") added ID
detection interrupt registers. However the current implementation assumes
that falling and rising edge interrupt are always enabled in registers
spanning over subsequent bits.
That is not the case for RK3128's version of the phy and this
implementation can't be used as-is, since there are bits with different
purpose in between.
This splits up the register definitions for id_det_en, id_det_en and
id_det_clr registers in rising and falling edge variants.
It's required as preparation to support RK3128's Innosilicon usb2 phy as
well in this driver and matches pretty much to what the vendor does, so I'm
not expecting issues for other SoCs with that change.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20231119121340.109025-2-knaerzche@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for drivers/phy/phy-can-transceiver.c
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20230714174841.4061919-1-robh@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This adds a bunch of new pixel clock- and tmds rates to the pre-pll
table which are required to get more VESA and some DMT rates working.
It has been completely re-calculated to match the min- and max-vco of
(750 MHz - 3.2 GHz) requirements. If more than one configuration would
have been possible the lowest fbdiv and refdiv (and therefore lowest
vco rate) has been preferred.
It's important to note, that RK3228 version of the phy does not support
fractional dividers. To support the most possible rates for this version
also in both 8-bit and 10-bit variant, some rates are not exact. The
maximum deviation of the pixel clock is 0.26, which perfectly fits into
VESA DMT recommendation of 0.5%.
I tested all possible rates on several screens from different
manufacturers with both RK3228 and RK3328. Both pre- and post-PLL
locking are slighlty faster now.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20230615171005.2251032-7-jonas@kwiboo.se
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Regular 8-bit and Deep Color video formats mainly differ in TMDS rate and
not in pixel clock rate.
When the hdmiphy clock is configured with the same pixel clock rate using
clk_set_rate() the clock framework do not signal the hdmi phy driver
to set_rate when switching between 8-bit and Deep Color.
This result in pre/post pll not being re-configured when switching between
regular 8-bit and Deep Color video formats.
Fix this by calling set_rate in power_on to force pre pll re-configuration.
Signed-off-by: Huicong Xu <xhc@rock-chips.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20230615171005.2251032-6-jonas@kwiboo.se
Signed-off-by: Vinod Koul <vkoul@kernel.org>
inno_write is used to configure 0xaa reg, that also hold the
POST_PLL_POWER_DOWN bit.
When POST_PLL_REFCLK_SEL_TMDS is configured the power down bit is not
taken into consideration.
Fix this by keeping the power down bit until configuration is complete.
Also reorder the reg write order for consistency.
Fixes: 53706a1168 ("phy: add Rockchip Innosilicon hdmi phy")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20230615171005.2251032-5-jonas@kwiboo.se
Signed-off-by: Vinod Koul <vkoul@kernel.org>
inno_hdmi_phy_rk3328_clk_recalc_rate() is returning a rate not found
in the pre pll config table when the fractal divider is used.
This can prevent proper power_on because a tmdsclock for the new rate
is not found in the pre pll config table.
Fix this by saving and returning a rounded pixel rate that exist
in the pre pll config table.
Fixes: 53706a1168 ("phy: add Rockchip Innosilicon hdmi phy")
Signed-off-by: Zheng Yang <zhengyang@rock-chips.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20230615171005.2251032-3-jonas@kwiboo.se
Signed-off-by: Vinod Koul <vkoul@kernel.org>
On RK3588 some registers need to be tweaked to support waking up from
suspend when a USB device is plugged into a port from a suspended PHY.
Without this change USB devices only work when they are plugged at
boot time.
Apart from that it optimizes settings to avoid devices toggling
between fullspeed and highspeed mode.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230522170324.61349-5-sebastian.reichel@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Cristian Ciocaltea
Algea Cao
Damon Ding
Andy Yan
Heiko Stuebner
Chukun Pan
Arnd Bergmann
Linus Torvalds
Sebastian Reichel
Niklas Cassel
Vinod Koul
Michal Tomek
Rick Wertenbroek
Krzysztof Kozlowski
Alex Bee
Rob Herring
Jagan Teki
Huicong Xu
Jonas Karlman
Zheng Yang
Yangtao Li
Tom Rix
Lucas Tanure