[ Upstream commit 8f7561209eda7d6998708f06376e8dd2dc52f3b8 ]
The rate validation in mac80211 considers a rate to be valid iff both
the rate index and the count are positive. When the rate scaling is
managed in the driver and not enough traffic passed to set the actual
rate, the driver set the rate to be the optimal rate. However, the rate
count is not set and thus the rate is considered not valid. Fix it by
setting the count to 1.
Fixes: 3e99b4d282 ("wifi: mac80211: Sanity check tx bitrate if not provided by driver")
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250503224232.0d1d1e022d63.I76833c14ba1d66f9bea5c32b25a54d8b36f229ba@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2e709805ce955f80803b7cab3421813c79e1df4 ]
The FW is now responsible of determining the SMPS mode.
If the user disabled power save in a certain vif, we send the vif-level
power command to clear out the POWER_FLAGS_POWER_MANAGEMENT_ENA_MSK bit
for that vif.
But erroneously, the FW checks DEVICE_POWER_FLAGS_POWER_SAVE_ENA_MSK in
the device-level command to determine the SMPS mode.
To W/A this, send also the device-level command when the power save of a
vif changes, and disable power save if there is any vif that has power
save disabled.
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308231427.7bf205efa027.I2c793ff1fc2a6779a95faaee1ded348100fd97f1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7774e3920029398ad49dc848b23840593f14d515 ]
The firmware dumps can be pretty big, and since we use single
pages for each SG table entry, even the table itself may end
up being an order-5 allocation. Build chained tables so that
we need not allocate a higher-order table here.
This could be improved and cleaned up, e.g. by using the SG
pool code or simply kvmalloc(), but all of that would require
also updating the devcoredump first since that frees it all,
so we need to be more careful. SG pool might also run against
the CONFIG_ARCH_NO_SG_CHAIN limitation, which is irrelevant
here.
Also use _devcd_free_sgtable() for the error paths now, much
simpler especially since it's in two places now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250209143303.697c7a465ac9.Iea982df46b5c075bfb77ade36f187d99a70c63db@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8c8a03e9b7bfc06f366b75daf3d0812400e7123 ]
When MSI-X is not enabled, we mask all the interrupts in the interrupt
handler and re-enable them when the interrupt thread runs. If
STATUS_INT_ENABLED is not set, we won't re-enable in the thread.
In order to get the ALIVE interrupt, we allow the ALIVE interrupt
itself, and RX as well in order to receive the ALIVE notification (which
is received as an RX from the firmware.
The problem is that STATUS_INT_ENABLED is clear until the op_mode calls
trans_fw_alive which means that until trans_fw_alive is called, any
notification from the firmware will not be received.
This became a problem when we inserted the pnvm_load exactly between the
ALIVE and trans_fw_alive.
Fix that by calling trans_fw_alive before loading the PNVM. This will
allow to get the notification from the firmware about PNVM load being
complete and continue the flow normally.
This didn't happen on MSI-X because we don't disable the interrupts in
the ISR when MSI-X is available.
The error in the log looks like this:
iwlwifi 0000:00:03.0: Timeout waiting for PNVM load!
iwlwifi 0000:00:03.0: Failed to start RT ucode: -110
iwlwifi 0000:00:03.0: WRT: Collecting data: ini trigger 13 fired (delay=0ms).
Fixes: 70d3ca86b0 ("iwlwifi: mvm: ring the doorbell and wait for PNVM load completion")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250306122425.0f2cf207aae1.I025d8f724b44f52eadf6c19069352eb9275613a8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9751163bffd3fe60794929829f810968c6de73d ]
If the firmware fails to start the session protection, then we
do call iwl_mvm_roc_finished() here, but that won't do anything
at all because IWL_MVM_STATUS_ROC_P2P_RUNNING was never set.
Set IWL_MVM_STATUS_ROC_P2P_RUNNING in the failure/stop path.
If it started successfully before, it's already set, so that
doesn't matter, and if it didn't start it needs to be set to
clean up.
Not doing so will lead to a WARN_ON() later on a fresh remain-
on-channel, since the link is already active when activated as
it was never deactivated.
Fixes: 35c1bbd93c ("wifi: iwlwifi: mvm: remove IWL_MVM_STATUS_NEED_FLUSH_P2P")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250209143303.0fe36c291068.I67f5dac742170dd937f11e4d4f937f45f71b7cb4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80e96206a3ef348fbd658d98f2f43149c36df8bc ]
A caller of iwl_acpi_get_dsm_object must free the returned object.
iwl_acpi_get_dsm_integer returns immediately without freeing
it if the expected size is more than 8 bytes. Fix that.
Note that with the current code this will never happen, since the caller
of iwl_acpi_get_dsm_integer already checks that the expected size if
either 1 or 4 bytes, so it can't exceed 8 bytes.
While at it, print the DSM value instead of the return value, as this
was the intention in the first place.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241228223206.bf61eaab99f8.Ibdc5df02f885208c222456d42c889c43b7e3b2f7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cc0c53f4fac562efb3aca2bc493515e77642ae33 upstream.
Both struct cfg80211_wowlan_nd_match and struct cfg80211_wowlan_nd_info
pre-allocate space for channels and matches, but then may end up using
fewer that the full allocation. Shrink the associated counter
(n_channels and n_matches) after counting the results. This avoids
compile-time (and run-time) warnings from __counted_by. (The counter
member needs to be updated _before_ accessing the array index.)
Seen with coming GCC 15:
drivers/net/wireless/intel/iwlwifi/mvm/d3.c: In function 'iwl_mvm_query_set_freqs':
drivers/net/wireless/intel/iwlwifi/mvm/d3.c:2877:66: warning: operation on 'match->n_channels' may be undefined [-Wsequence-point]
2877 | match->channels[match->n_channels++] =
| ~~~~~~~~~~~~~~~~~^~
drivers/net/wireless/intel/iwlwifi/mvm/d3.c:2885:66: warning: operation on 'match->n_channels' may be undefined [-Wsequence-point]
2885 | match->channels[match->n_channels++] =
| ~~~~~~~~~~~~~~~~~^~
drivers/net/wireless/intel/iwlwifi/mvm/d3.c: In function 'iwl_mvm_query_netdetect_reasons':
drivers/net/wireless/intel/iwlwifi/mvm/d3.c:2982:58: warning: operation on 'net_detect->n_matches' may be undefined [-Wsequence-point]
2982 | net_detect->matches[net_detect->n_matches++] = match;
| ~~~~~~~~~~~~~~~~~~~~~^~
Cc: stable@vger.kernel.org
Fixes: aa4ec06c45 ("wifi: cfg80211: use __counted_by where appropriate")
Signed-off-by: Kees Cook <kees@kernel.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://patch.msgid.link/20240619211233.work.355-kees@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 11ac0d7c3b5ba58232fb7dacb54371cbe75ec183 ]
If we got an unprotected action frame with CSA and then we heard the
beacon with the CSA IE, we'll block the queues with the CSA reason
twice. Since this reason is refcounted, we won't wake up the queues
since we wake them up only once and the ref count will never reach 0.
This led to blocked queues that prevented any activity (even
disconnection wouldn't reset the queue state and the only way to recover
would be to reload the kernel module.
Fix this by not refcounting the CSA reason.
It becomes now pointless to maintain the csa_blocked_queues state.
Remove it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: 414e090bc4 ("wifi: mac80211: restrict public action ECSA frame handling")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219447
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241119173108.5ea90828c2cc.I4f89e58572fb71ae48e47a81e74595cac410fbac@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1a54ec21b8e7bca59141ff1ac6ce73e07d744f2 ]
Since we no longer shut down the device in suspend, we also no longer
call iwl_mvm_mei_device_state() and this is a problem because iwlmei
expects this to be called when it runs its own suspend sequence. It
checks mei->device_down in iwl_mei_remove() which is called upon
suspend.
Fix this by telling iwlmei when we're done accessing the device.
When we'll wake up, the device should be untouched if CSME didn't use it
during the suspend time. If CSME used it, we'll notice it through the
CSR_FUNC_SCRATCH register.
Fixes: e8bb19c1d5 ("wifi: iwlwifi: support fast resume")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241028135215.525287b90af2.Ibf183824471ea5580d9276d104444e53191e6900@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
If more than 255 colocated APs exist for the set of all
APs found during 2.4/5 GHz scanning, then the 6 GHz scan
construction will loop forever since the loop variable
has type u8, which can never reach the number found when
that's bigger than 255, and is stored in a u32 variable.
Also move it into the loops to have a smaller scope.
Using a u32 there is fine, we limit the number of APs in
the scan list and each has a limit on the number of RNR
entries due to the frame size. With a limit of 1000 scan
results, a frame size upper bound of 4096 (really it's
more like ~2300) and a TBTT entry size of at least 11,
we get an upper bound for the number of ~372k, well in
the bounds of a u32.
Cc: stable@vger.kernel.org
Fixes: eae94cf82d ("iwlwifi: mvm: add support for 6GHz")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219375
Link: https://patch.msgid.link/20241023091744.f4baed5c08a1.I8b417148bbc8c5d11c101e1b8f5bf372e17bf2a7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Revert commit dfdfe4be18 ("wifi: iwlwifi: remove retry loops in
start"), it turns out that there's an issue with the PNVM load
notification from firmware not getting processed, that this patch
has been somewhat successfully papering over. Since this is being
reported, revert the loop removal for now.
We will later at least clean this up to only attempt to retry if
there was a timeout, but currently we don't even bubble up the
failure reason to the correct layer, only returning NULL.
Fixes: dfdfe4be18 ("wifi: iwlwifi: remove retry loops in start")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20241022092212.4aa82a558a00.Ibdeff9c8f0d608bc97fc42024392ae763b6937b7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we add the vif (and its default link) in fw restart we may
override the link that already exists. We take care of this but if
link 0 is a valid MLO link, then we will re-create a default link on
mvmvif->link[0] and we'll loose the real link we had there.
In non-MLO, we need to re-create the default link upon the interface
creation, this is fine. In MLO, we'll just wait for change_vif_links()
to re-build the links.
Fixes: bf976c814c ("wifi: iwlwifi: mvm: implement link change ops")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241010140328.385bfea1b2e9.I4a127312285ccb529cc95cc4edf6fbe1e0a136ad@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwl_mvm_send_ap_tx_power_constraint_cmd is a no-op if the link is not
active (we need to know the band etc.)
However, for the station case it will be called just before we set the
link to active (by calling iwl_mvm_link_changed with
the LINK_CONTEXT_MODIFY_ACTIVE bit set in the 'changed' flags and
active = true), so it will end up doing nothing.
Fix this by calling iwl_mvm_send_ap_tx_power_constraint_cmd before
iwl_mvm_link_changed.
Fixes: 6b82f4e119 ("wifi: iwlwifi: mvm: handle TPE advertised by AP")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241010140328.5c235fccd3f1.I2d40dea21e5547eba458565edcb4c354d094d82a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
wireless fixes for v6.12-rc5
The first set of wireless fixes for v6.12. We have been busy and have
not been able to send this earlier, so there are more fixes than
usual. The fixes are all over, both in stack and in drivers, but
nothing special really standing out.
-Wflex-array-member-not-at-end was introduced in GCC-14, and we are
getting ready to enable it, globally.
So, in order to avoid ending up with a flexible-array member in the
middle of multiple other structs, we use the `__struct_group()`
helper to create a new tagged `struct ieee80211_radiotap_header_fixed`.
This structure groups together all the members of the flexible
`struct ieee80211_radiotap_header` except the flexible array.
As a result, the array is effectively separated from the rest of the
members without modifying the memory layout of the flexible structure.
We then change the type of the middle struct members currently causing
trouble from `struct ieee80211_radiotap_header` to `struct
ieee80211_radiotap_header_fixed`.
We also want to ensure that in case new members need to be added to the
flexible structure, they are always included within the newly created
tagged struct. For this, we use `static_assert()`. This ensures that the
memory layout for both the flexible structure and the new tagged struct
is the same after any changes.
This approach avoids having to implement `struct ieee80211_radiotap_header_fixed`
as a completely separate structure, thus preventing having to maintain
two independent but basically identical structures, closing the door
to potential bugs in the future.
So, with these changes, fix the following warnings:
drivers/net/wireless/ath/wil6210/txrx.c:309:50: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/intel/ipw2x00/ipw2100.c:2521:50: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/intel/ipw2x00/ipw2200.h:1146:42: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/intel/ipw2x00/libipw.h:595:36: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/marvell/libertas/radiotap.h:34:42: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/marvell/libertas/radiotap.h:5:42: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/microchip/wilc1000/mon.c:10:42: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/microchip/wilc1000/mon.c:15:42: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/virtual/mac80211_hwsim.c:758:42: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/virtual/mac80211_hwsim.c:767:42: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://patch.msgid.link/ZwBMtBZKcrzwU7l4@kspp
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
no_llseek had been defined to NULL two years ago, in commit 868941b144
("fs: remove no_llseek")
To quote that commit,
At -rc1 we'll need do a mechanical removal of no_llseek -
git grep -l -w no_llseek | grep -v porting.rst | while read i; do
sed -i '/\<no_llseek\>/d' $i
done
would do it.
Unfortunately, that hadn't been done. Linus, could you do that now, so
that we could finally put that thing to rest? All instances are of the
form
.llseek = no_llseek,
so it's obviously safe.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>