Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (64 commits)
  Input: tc3589x-keypad - add missing kerneldoc
  Input: ucb1400-ts - switch to using dev_xxx() for diagnostic messages
  Input: ucb1400_ts - convert to threaded IRQ
  Input: ucb1400_ts - drop inline annotations
  Input: usb1400_ts - add __devinit/__devexit section annotations
  Input: ucb1400_ts - set driver owner
  Input: ucb1400_ts - convert to use dev_pm_ops
  Input: psmouse - make sure we do not use stale methods
  Input: evdev - do not block waiting for an event if fd is nonblock
  Input: evdev - if no events and non-block, return EAGAIN not 0
  Input: evdev - only allow reading events if a full packet is present
  Input: add driver for pixcir i2c touchscreens
  Input: samsung-keypad - implement runtime power management support
  Input: tegra-kbc - report wakeup key for some platforms
  Input: tegra-kbc - add device tree bindings
  Input: add driver for AUO In-Cell touchscreens using pixcir ICs
  Input: mpu3050 - configure the sampling method
  Input: mpu3050 - ensure we enable interrupts
  Input: mpu3050 - add of_match table for device-tree probing
  Input: sentelic - document the latest hardware
  ...

Fix up fairly trivial conflicts (device tree matching conflicting with
some independent cleanups) in drivers/input/keyboard/samsung-keypad.c

drivers/input/misc/88pm860x_onkey.c

@@ -137,18 +137,7 @@ static struct platform_driver pm860x_onkey_driver = {
 	.probe		= pm860x_onkey_probe,
 	.remove		= __devexit_p(pm860x_onkey_remove),
 };
-
-static int __init pm860x_onkey_init(void)
-{
-	return platform_driver_register(&pm860x_onkey_driver);
-}
-module_init(pm860x_onkey_init);
-
-static void __exit pm860x_onkey_exit(void)
-{
-	platform_driver_unregister(&pm860x_onkey_driver);
-}
-module_exit(pm860x_onkey_exit);
+module_platform_driver(pm860x_onkey_driver);
 
 MODULE_DESCRIPTION("Marvell 88PM860x ONKEY driver");
 MODULE_AUTHOR("Haojian Zhuang <haojian.zhuang@marvell.com>");

drivers/input/misc/Kconfig

@@ -179,6 +179,31 @@ config INPUT_APANEL
 	 To compile this driver as a module, choose M here: the module will
 	 be called apanel.
 
+config INPUT_GP2A
+	tristate "Sharp GP2AP002A00F I2C Proximity/Opto sensor driver"
+	depends on I2C
+	depends on GENERIC_GPIO
+	help
+	  Say Y here if you have a Sharp GP2AP002A00F proximity/als combo-chip
+	  hooked to an I2C bus.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called gp2ap002a00f.
+
+config INPUT_GPIO_TILT_POLLED
+	tristate "Polled GPIO tilt switch"
+	depends on GENERIC_GPIO
+	select INPUT_POLLDEV
+	help
+	  This driver implements support for tilt switches connected
+	  to GPIO pins that are not capable of generating interrupts.
+
+	  The list of gpios to use and the mapping of their states
+	  to specific angles is done via platform data.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called gpio_tilt_polled.
+
 config INPUT_IXP4XX_BEEPER
 	tristate "IXP4XX Beeper support"
 	depends on ARCH_IXP4XX

drivers/input/misc/Makefile

@@ -22,6 +22,8 @@ obj-$(CONFIG_INPUT_CMA3000)		+= cma3000_d0x.o
 obj-$(CONFIG_INPUT_CMA3000_I2C)		+= cma3000_d0x_i2c.o
 obj-$(CONFIG_INPUT_COBALT_BTNS)		+= cobalt_btns.o
 obj-$(CONFIG_INPUT_DM355EVM)		+= dm355evm_keys.o
+obj-$(CONFIG_INPUT_GP2A)		+= gp2ap002a00f.o
+obj-$(CONFIG_INPUT_GPIO_TILT_POLLED)	+= gpio_tilt_polled.o
 obj-$(CONFIG_HP_SDC_RTC)		+= hp_sdc_rtc.o
 obj-$(CONFIG_INPUT_IXP4XX_BEEPER)	+= ixp4xx-beeper.o
 obj-$(CONFIG_INPUT_KEYSPAN_REMOTE)	+= keyspan_remote.o

drivers/input/misc/ab8500-ponkey.c

@@ -139,18 +139,7 @@ static struct platform_driver ab8500_ponkey_driver = {
 	.probe		= ab8500_ponkey_probe,
 	.remove		= __devexit_p(ab8500_ponkey_remove),
 };
-
-static int __init ab8500_ponkey_init(void)
-{
-	return platform_driver_register(&ab8500_ponkey_driver);
-}
-module_init(ab8500_ponkey_init);
-
-static void __exit ab8500_ponkey_exit(void)
-{
-	platform_driver_unregister(&ab8500_ponkey_driver);
-}
-module_exit(ab8500_ponkey_exit);
+module_platform_driver(ab8500_ponkey_driver);
 
 MODULE_LICENSE("GPL v2");
 MODULE_AUTHOR("Sundar Iyer <sundar.iyer@stericsson.com>");

drivers/input/misc/adxl34x-spi.c

@@ -122,7 +122,6 @@ static SIMPLE_DEV_PM_OPS(adxl34x_spi_pm, adxl34x_spi_suspend,
 static struct spi_driver adxl34x_driver = {
 	.driver = {
 		.name = "adxl34x",
-		.bus = &spi_bus_type,
 		.owner = THIS_MODULE,
 		.pm = &adxl34x_spi_pm,
 	},

drivers/input/misc/adxl34x.c

@@ -452,10 +452,10 @@ static ssize_t adxl34x_disable_store(struct device *dev,
 				     const char *buf, size_t count)
 {
 	struct adxl34x *ac = dev_get_drvdata(dev);
-	unsigned long val;
+	unsigned int val;
 	int error;
 
-	error = strict_strtoul(buf, 10, &val);
+	error = kstrtouint(buf, 10, &val);
 	if (error)
 		return error;
 
@@ -541,10 +541,10 @@ static ssize_t adxl34x_rate_store(struct device *dev,
 				  const char *buf, size_t count)
 {
 	struct adxl34x *ac = dev_get_drvdata(dev);
-	unsigned long val;
+	unsigned char val;
 	int error;
 
-	error = strict_strtoul(buf, 10, &val);
+	error = kstrtou8(buf, 10, &val);
 	if (error)
 		return error;
 
@@ -576,10 +576,10 @@ static ssize_t adxl34x_autosleep_store(struct device *dev,
 				  const char *buf, size_t count)
 {
 	struct adxl34x *ac = dev_get_drvdata(dev);
-	unsigned long val;
+	unsigned int val;
 	int error;
 
-	error = strict_strtoul(buf, 10, &val);
+	error = kstrtouint(buf, 10, &val);
 	if (error)
 		return error;
 
@@ -623,13 +623,13 @@ static ssize_t adxl34x_write_store(struct device *dev,
 				   const char *buf, size_t count)
 {
 	struct adxl34x *ac = dev_get_drvdata(dev);
-	unsigned long val;
+	unsigned int val;
 	int error;
 
 	/*
 	 * This allows basic ADXL register write access for debug purposes.
 	 */
-	error = strict_strtoul(buf, 16, &val);
+	error = kstrtouint(buf, 16, &val);
 	if (error)
 		return error;
 

drivers/input/misc/ati_remote2.c

@@ -42,13 +42,13 @@ static int ati_remote2_set_mask(const char *val,
 				const struct kernel_param *kp,
 				unsigned int max)
 {
-	unsigned long mask;
+	unsigned int mask;
 	int ret;
 
 	if (!val)
 		return -EINVAL;
 
-	ret = strict_strtoul(val, 0, &mask);
+	ret = kstrtouint(val, 0, &mask);
 	if (ret)
 		return ret;
 
@@ -720,11 +720,12 @@ static ssize_t ati_remote2_store_channel_mask(struct device *dev,
 	struct usb_device *udev = to_usb_device(dev);
 	struct usb_interface *intf = usb_ifnum_to_if(udev, 0);
 	struct ati_remote2 *ar2 = usb_get_intfdata(intf);
-	unsigned long mask;
+	unsigned int mask;
 	int r;
 
-	if (strict_strtoul(buf, 0, &mask))
-		return -EINVAL;
+	r = kstrtouint(buf, 0, &mask);
+	if (r)
+		return r;
 
 	if (mask & ~ATI_REMOTE2_MAX_CHANNEL_MASK)
 		return -EINVAL;
@@ -769,10 +770,12 @@ static ssize_t ati_remote2_store_mode_mask(struct device *dev,
 	struct usb_device *udev = to_usb_device(dev);
 	struct usb_interface *intf = usb_ifnum_to_if(udev, 0);
 	struct ati_remote2 *ar2 = usb_get_intfdata(intf);
-	unsigned long mask;
+	unsigned int mask;
+	int err;
 
-	if (strict_strtoul(buf, 0, &mask))
-		return -EINVAL;
+	err = kstrtouint(buf, 0, &mask);
+	if (err)
+		return err;
 
 	if (mask & ~ATI_REMOTE2_MAX_MODE_MASK)
 		return -EINVAL;

drivers/input/misc/bfin_rotary.c

@@ -264,18 +264,7 @@ static struct platform_driver bfin_rotary_device_driver = {
 #endif
 	},
 };
-
-static int __init bfin_rotary_init(void)
-{
-	return platform_driver_register(&bfin_rotary_device_driver);
-}
-module_init(bfin_rotary_init);
-
-static void __exit bfin_rotary_exit(void)
-{
-	platform_driver_unregister(&bfin_rotary_device_driver);
-}
-module_exit(bfin_rotary_exit);
+module_platform_driver(bfin_rotary_device_driver);
 
 MODULE_LICENSE("GPL");
 MODULE_AUTHOR("Michael Hennerich <hennerich@blackfin.uclinux.org>");

drivers/input/misc/cobalt_btns.c

@@ -163,16 +163,4 @@ static struct platform_driver cobalt_buttons_driver = {
 		.owner	= THIS_MODULE,
 	},
 };
-
-static int __init cobalt_buttons_init(void)
-{
-	return platform_driver_register(&cobalt_buttons_driver);
-}
-
-static void __exit cobalt_buttons_exit(void)
-{
-	platform_driver_unregister(&cobalt_buttons_driver);
-}
-
-module_init(cobalt_buttons_init);
-module_exit(cobalt_buttons_exit);
+module_platform_driver(cobalt_buttons_driver);

drivers/input/misc/dm355evm_keys.c

@@ -267,17 +267,6 @@ static struct platform_driver dm355evm_keys_driver = {
 		.name	= "dm355evm_keys",
 	},
 };
-
-static int __init dm355evm_keys_init(void)
-{
-	return platform_driver_register(&dm355evm_keys_driver);
-}
-module_init(dm355evm_keys_init);
-
-static void __exit dm355evm_keys_exit(void)
-{
-	platform_driver_unregister(&dm355evm_keys_driver);
-}
-module_exit(dm355evm_keys_exit);
+module_platform_driver(dm355evm_keys_driver);
 
 MODULE_LICENSE("GPL");

drivers/input/misc/gp2ap002a00f.c

@@ -0,0 +1,299 @@
+/*
+ * Copyright (C) 2011 Sony Ericsson Mobile Communications Inc.
+ *
+ * Author: Courtney Cavin <courtney.cavin@sonyericsson.com>
+ * Prepared for up-stream by: Oskar Andero <oskar.andero@sonyericsson.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2, as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/i2c.h>
+#include <linux/irq.h>
+#include <linux/slab.h>
+#include <linux/input.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/gpio.h>
+#include <linux/delay.h>
+#include <linux/input/gp2ap002a00f.h>
+
+struct gp2a_data {
+	struct input_dev *input;
+	const struct gp2a_platform_data *pdata;
+	struct i2c_client *i2c_client;
+};
+
+enum gp2a_addr {
+	GP2A_ADDR_PROX	= 0x0,
+	GP2A_ADDR_GAIN	= 0x1,
+	GP2A_ADDR_HYS	= 0x2,
+	GP2A_ADDR_CYCLE	= 0x3,
+	GP2A_ADDR_OPMOD	= 0x4,
+	GP2A_ADDR_CON	= 0x6
+};
+
+enum gp2a_controls {
+	/* Software Shutdown control: 0 = shutdown, 1 = normal operation */
+	GP2A_CTRL_SSD	= 0x01
+};
+
+static int gp2a_report(struct gp2a_data *dt)
+{
+	int vo = gpio_get_value(dt->pdata->vout_gpio);
+
+	input_report_switch(dt->input, SW_FRONT_PROXIMITY, !vo);
+	input_sync(dt->input);
+
+	return 0;
+}
+
+static irqreturn_t gp2a_irq(int irq, void *handle)
+{
+	struct gp2a_data *dt = handle;
+
+	gp2a_report(dt);
+
+	return IRQ_HANDLED;
+}
+
+static int gp2a_enable(struct gp2a_data *dt)
+{
+	return i2c_smbus_write_byte_data(dt->i2c_client, GP2A_ADDR_OPMOD,
+					 GP2A_CTRL_SSD);
+}
+
+static int gp2a_disable(struct gp2a_data *dt)
+{
+	return i2c_smbus_write_byte_data(dt->i2c_client, GP2A_ADDR_OPMOD,
+					 0x00);
+}
+
+static int gp2a_device_open(struct input_dev *dev)
+{
+	struct gp2a_data *dt = input_get_drvdata(dev);
+	int error;
+
+	error = gp2a_enable(dt);
+	if (error < 0) {
+		dev_err(&dt->i2c_client->dev,
+			"unable to activate, err %d\n", error);
+		return error;
+	}
+
+	gp2a_report(dt);
+
+	return 0;
+}
+
+static void gp2a_device_close(struct input_dev *dev)
+{
+	struct gp2a_data *dt = input_get_drvdata(dev);
+	int error;
+
+	error = gp2a_disable(dt);
+	if (error < 0)
+		dev_err(&dt->i2c_client->dev,
+			"unable to deactivate, err %d\n", error);
+}
+
+static int __devinit gp2a_initialize(struct gp2a_data *dt)
+{
+	int error;
+
+	error = i2c_smbus_write_byte_data(dt->i2c_client, GP2A_ADDR_GAIN,
+					  0x08);
+	if (error < 0)
+		return error;
+
+	error = i2c_smbus_write_byte_data(dt->i2c_client, GP2A_ADDR_HYS,
+					  0xc2);
+	if (error < 0)
+		return error;
+
+	error = i2c_smbus_write_byte_data(dt->i2c_client, GP2A_ADDR_CYCLE,
+					  0x04);
+	if (error < 0)
+		return error;
+
+	error = gp2a_disable(dt);
+
+	return error;
+}
+
+static int __devinit gp2a_probe(struct i2c_client *client,
+				const struct i2c_device_id *id)
+{
+	const struct gp2a_platform_data *pdata = client->dev.platform_data;
+	struct gp2a_data *dt;
+	int error;
+
+	if (!pdata)
+		return -EINVAL;
+
+	if (pdata->hw_setup) {
+		error = pdata->hw_setup(client);
+		if (error < 0)
+			return error;
+	}
+
+	error = gpio_request_one(pdata->vout_gpio, GPIOF_IN, GP2A_I2C_NAME);
+	if (error)
+		goto err_hw_shutdown;
+
+	dt = kzalloc(sizeof(struct gp2a_data), GFP_KERNEL);
+	if (!dt) {
+		error = -ENOMEM;
+		goto err_free_gpio;
+	}
+
+	dt->pdata = pdata;
+	dt->i2c_client = client;
+
+	error = gp2a_initialize(dt);
+	if (error < 0)
+		goto err_free_mem;
+
+	dt->input = input_allocate_device();
+	if (!dt->input) {
+		error = -ENOMEM;
+		goto err_free_mem;
+	}
+
+	input_set_drvdata(dt->input, dt);
+
+	dt->input->open = gp2a_device_open;
+	dt->input->close = gp2a_device_close;
+	dt->input->name = GP2A_I2C_NAME;
+	dt->input->id.bustype = BUS_I2C;
+	dt->input->dev.parent = &client->dev;
+
+	input_set_capability(dt->input, EV_SW, SW_FRONT_PROXIMITY);
+
+	error = request_threaded_irq(client->irq, NULL, gp2a_irq,
+			IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING |
+				IRQF_ONESHOT,
+			GP2A_I2C_NAME, dt);
+	if (error) {
+		dev_err(&client->dev, "irq request failed\n");
+		goto err_free_input_dev;
+	}
+
+	error = input_register_device(dt->input);
+	if (error) {
+		dev_err(&client->dev, "device registration failed\n");
+		goto err_free_irq;
+	}
+
+	device_init_wakeup(&client->dev, pdata->wakeup);
+	i2c_set_clientdata(client, dt);
+
+	return 0;
+
+err_free_irq:
+	free_irq(client->irq, dt);
+err_free_input_dev:
+	input_free_device(dt->input);
+err_free_mem:
+	kfree(dt);
+err_free_gpio:
+	gpio_free(pdata->vout_gpio);
+err_hw_shutdown:
+	if (pdata->hw_shutdown)
+		pdata->hw_shutdown(client);
+	return error;
+}
+
+static int __devexit gp2a_remove(struct i2c_client *client)
+{
+	struct gp2a_data *dt = i2c_get_clientdata(client);
+	const struct gp2a_platform_data *pdata = dt->pdata;
+
+	device_init_wakeup(&client->dev, false);
+
+	free_irq(client->irq, dt);
+
+	input_unregister_device(dt->input);
+	kfree(dt);
+
+	gpio_free(pdata->vout_gpio);
+
+	if (pdata->hw_shutdown)
+		pdata->hw_shutdown(client);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int gp2a_suspend(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct gp2a_data *dt = i2c_get_clientdata(client);
+	int retval = 0;
+
+	if (device_may_wakeup(&client->dev)) {
+		enable_irq_wake(client->irq);
+	} else {
+		mutex_lock(&dt->input->mutex);
+		if (dt->input->users)
+			retval = gp2a_disable(dt);
+		mutex_unlock(&dt->input->mutex);
+	}
+
+	return retval;
+}
+
+static int gp2a_resume(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct gp2a_data *dt = i2c_get_clientdata(client);
+	int retval = 0;
+
+	if (device_may_wakeup(&client->dev)) {
+		disable_irq_wake(client->irq);
+	} else {
+		mutex_lock(&dt->input->mutex);
+		if (dt->input->users)
+			retval = gp2a_enable(dt);
+		mutex_unlock(&dt->input->mutex);
+	}
+
+	return retval;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(gp2a_pm, gp2a_suspend, gp2a_resume);
+
+static const struct i2c_device_id gp2a_i2c_id[] = {
+	{ GP2A_I2C_NAME, 0 },
+	{ }
+};
+
+static struct i2c_driver gp2a_i2c_driver = {
+	.driver = {
+		.name	= GP2A_I2C_NAME,
+		.owner	= THIS_MODULE,
+		.pm	= &gp2a_pm,
+	},
+	.probe		= gp2a_probe,
+	.remove		= __devexit_p(gp2a_remove),
+	.id_table	= gp2a_i2c_id,
+};
+
+static int __init gp2a_init(void)
+{
+	return i2c_add_driver(&gp2a_i2c_driver);
+}
+
+static void __exit gp2a_exit(void)
+{
+	i2c_del_driver(&gp2a_i2c_driver);
+}
+
+module_init(gp2a_init);
+module_exit(gp2a_exit);
+
+MODULE_AUTHOR("Courtney Cavin <courtney.cavin@sonyericsson.com>");
+MODULE_DESCRIPTION("Sharp GP2AP002A00F I2C Proximity/Opto sensor driver");
+MODULE_LICENSE("GPL v2");

drivers/input/misc/gpio_tilt_polled.c

@@ -0,0 +1,213 @@
+/*
+ *  Driver for tilt switches connected via GPIO lines
+ *  not capable of generating interrupts
+ *
+ *  Copyright (C) 2011 Heiko Stuebner <heiko@sntech.de>
+ *
+ *  based on: drivers/input/keyboard/gpio_keys_polled.c
+ *
+ *  Copyright (C) 2007-2010 Gabor Juhos <juhosg@openwrt.org>
+ *  Copyright (C) 2010 Nuno Goncalves <nunojpg@gmail.com>
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License version 2 as
+ *  published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/input.h>
+#include <linux/input-polldev.h>
+#include <linux/ioport.h>
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+#include <linux/input/gpio_tilt.h>
+
+#define DRV_NAME	"gpio-tilt-polled"
+
+struct gpio_tilt_polled_dev {
+	struct input_polled_dev *poll_dev;
+	struct device *dev;
+	const struct gpio_tilt_platform_data *pdata;
+
+	int last_state;
+
+	int threshold;
+	int count;
+};
+
+static void gpio_tilt_polled_poll(struct input_polled_dev *dev)
+{
+	struct gpio_tilt_polled_dev *tdev = dev->private;
+	const struct gpio_tilt_platform_data *pdata = tdev->pdata;
+	struct input_dev *input = dev->input;
+	struct gpio_tilt_state *tilt_state = NULL;
+	int state, i;
+
+	if (tdev->count < tdev->threshold) {
+		tdev->count++;
+	} else {
+		state = 0;
+		for (i = 0; i < pdata->nr_gpios; i++)
+			state |= (!!gpio_get_value(pdata->gpios[i].gpio) << i);
+
+		if (state != tdev->last_state) {
+			for (i = 0; i < pdata->nr_states; i++)
+				if (pdata->states[i].gpios == state)
+					tilt_state = &pdata->states[i];
+
+			if (tilt_state) {
+				for (i = 0; i < pdata->nr_axes; i++)
+					input_report_abs(input,
+							 pdata->axes[i].axis,
+							 tilt_state->axes[i]);
+
+				input_sync(input);
+			}
+
+			tdev->count = 0;
+			tdev->last_state = state;
+		}
+	}
+}
+
+static void gpio_tilt_polled_open(struct input_polled_dev *dev)
+{
+	struct gpio_tilt_polled_dev *tdev = dev->private;
+	const struct gpio_tilt_platform_data *pdata = tdev->pdata;
+
+	if (pdata->enable)
+		pdata->enable(tdev->dev);
+
+	/* report initial state of the axes */
+	tdev->last_state = -1;
+	tdev->count = tdev->threshold;
+	gpio_tilt_polled_poll(tdev->poll_dev);
+}
+
+static void gpio_tilt_polled_close(struct input_polled_dev *dev)
+{
+	struct gpio_tilt_polled_dev *tdev = dev->private;
+	const struct gpio_tilt_platform_data *pdata = tdev->pdata;
+
+	if (pdata->disable)
+		pdata->disable(tdev->dev);
+}
+
+static int __devinit gpio_tilt_polled_probe(struct platform_device *pdev)
+{
+	const struct gpio_tilt_platform_data *pdata = pdev->dev.platform_data;
+	struct device *dev = &pdev->dev;
+	struct gpio_tilt_polled_dev *tdev;
+	struct input_polled_dev *poll_dev;
+	struct input_dev *input;
+	int error, i;
+
+	if (!pdata || !pdata->poll_interval)
+		return -EINVAL;
+
+	tdev = kzalloc(sizeof(struct gpio_tilt_polled_dev), GFP_KERNEL);
+	if (!tdev) {
+		dev_err(dev, "no memory for private data\n");
+		return -ENOMEM;
+	}
+
+	error = gpio_request_array(pdata->gpios, pdata->nr_gpios);
+	if (error) {
+		dev_err(dev,
+			"Could not request tilt GPIOs: %d\n", error);
+		goto err_free_tdev;
+	}
+
+	poll_dev = input_allocate_polled_device();
+	if (!poll_dev) {
+		dev_err(dev, "no memory for polled device\n");
+		error = -ENOMEM;
+		goto err_free_gpios;
+	}
+
+	poll_dev->private = tdev;
+	poll_dev->poll = gpio_tilt_polled_poll;
+	poll_dev->poll_interval = pdata->poll_interval;
+	poll_dev->open = gpio_tilt_polled_open;
+	poll_dev->close = gpio_tilt_polled_close;
+
+	input = poll_dev->input;
+
+	input->name = pdev->name;
+	input->phys = DRV_NAME"/input0";
+	input->dev.parent = &pdev->dev;
+
+	input->id.bustype = BUS_HOST;
+	input->id.vendor = 0x0001;
+	input->id.product = 0x0001;
+	input->id.version = 0x0100;
+
+	__set_bit(EV_ABS, input->evbit);
+	for (i = 0; i < pdata->nr_axes; i++)
+		input_set_abs_params(input, pdata->axes[i].axis,
+				     pdata->axes[i].min, pdata->axes[i].max,
+				     pdata->axes[i].fuzz, pdata->axes[i].flat);
+
+	tdev->threshold = DIV_ROUND_UP(pdata->debounce_interval,
+				       pdata->poll_interval);
+
+	tdev->poll_dev = poll_dev;
+	tdev->dev = dev;
+	tdev->pdata = pdata;
+
+	error = input_register_polled_device(poll_dev);
+	if (error) {
+		dev_err(dev, "unable to register polled device, err=%d\n",
+			error);
+		goto err_free_polldev;
+	}
+
+	platform_set_drvdata(pdev, tdev);
+
+	return 0;
+
+err_free_polldev:
+	input_free_polled_device(poll_dev);
+err_free_gpios:
+	gpio_free_array(pdata->gpios, pdata->nr_gpios);
+err_free_tdev:
+	kfree(tdev);
+
+	return error;
+}
+
+static int __devexit gpio_tilt_polled_remove(struct platform_device *pdev)
+{
+	struct gpio_tilt_polled_dev *tdev = platform_get_drvdata(pdev);
+	const struct gpio_tilt_platform_data *pdata = tdev->pdata;
+
+	platform_set_drvdata(pdev, NULL);
+
+	input_unregister_polled_device(tdev->poll_dev);
+	input_free_polled_device(tdev->poll_dev);
+
+	gpio_free_array(pdata->gpios, pdata->nr_gpios);
+
+	kfree(tdev);
+
+	return 0;
+}
+
+static struct platform_driver gpio_tilt_polled_driver = {
+	.probe	= gpio_tilt_polled_probe,
+	.remove	= __devexit_p(gpio_tilt_polled_remove),
+	.driver	= {
+		.name	= DRV_NAME,
+		.owner	= THIS_MODULE,
+	},
+};
+
+module_platform_driver(gpio_tilt_polled_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Heiko Stuebner <heiko@sntech.de>");
+MODULE_DESCRIPTION("Polled GPIO tilt driver");
+MODULE_ALIAS("platform:" DRV_NAME);

drivers/input/misc/ixp4xx-beeper.c

@@ -168,16 +168,5 @@ static struct platform_driver ixp4xx_spkr_platform_driver = {
 	.remove		= __devexit_p(ixp4xx_spkr_remove),
 	.shutdown	= ixp4xx_spkr_shutdown,
 };
+module_platform_driver(ixp4xx_spkr_platform_driver);
 
-static int __init ixp4xx_spkr_init(void)
-{
-	return platform_driver_register(&ixp4xx_spkr_platform_driver);
-}
-
-static void __exit ixp4xx_spkr_exit(void)
-{
-	platform_driver_unregister(&ixp4xx_spkr_platform_driver);
-}
-
-module_init(ixp4xx_spkr_init);
-module_exit(ixp4xx_spkr_exit);

drivers/input/misc/max8925_onkey.c

@@ -166,18 +166,7 @@ static struct platform_driver max8925_onkey_driver = {
 	.probe		= max8925_onkey_probe,
 	.remove		= __devexit_p(max8925_onkey_remove),
 };
-
-static int __init max8925_onkey_init(void)
-{
-	return platform_driver_register(&max8925_onkey_driver);
-}
-module_init(max8925_onkey_init);
-
-static void __exit max8925_onkey_exit(void)
-{
-	platform_driver_unregister(&max8925_onkey_driver);
-}
-module_exit(max8925_onkey_exit);
+module_platform_driver(max8925_onkey_driver);
 
 MODULE_DESCRIPTION("Maxim MAX8925 ONKEY driver");
 MODULE_AUTHOR("Haojian Zhuang <haojian.zhuang@marvell.com>");

drivers/input/misc/mc13783-pwrbutton.c

@@ -255,7 +255,7 @@ static int __devexit mc13783_pwrbutton_remove(struct platform_device *pdev)
 	return 0;
 }
 
-struct platform_driver mc13783_pwrbutton_driver = {
+static struct platform_driver mc13783_pwrbutton_driver = {
 	.probe		= mc13783_pwrbutton_probe,
 	.remove		= __devexit_p(mc13783_pwrbutton_remove),
 	.driver		= {
@@ -264,17 +264,7 @@ struct platform_driver mc13783_pwrbutton_driver = {
 	},
 };
 
-static int __init mc13783_pwrbutton_init(void)
-{
-	return platform_driver_register(&mc13783_pwrbutton_driver);
-}
-module_init(mc13783_pwrbutton_init);
-
-static void __exit mc13783_pwrbutton_exit(void)
-{
-	platform_driver_unregister(&mc13783_pwrbutton_driver);
-}
-module_exit(mc13783_pwrbutton_exit);
+module_platform_driver(mc13783_pwrbutton_driver);
 
 MODULE_ALIAS("platform:mc13783-pwrbutton");
 MODULE_DESCRIPTION("MC13783 Power Button");

drivers/input/misc/mpu3050.c

@@ -41,18 +41,67 @@
 #include <linux/slab.h>
 #include <linux/pm_runtime.h>
 
-#define MPU3050_CHIP_ID_REG	0x00
 #define MPU3050_CHIP_ID		0x69
-#define MPU3050_XOUT_H		0x1D
-#define MPU3050_PWR_MGM		0x3E
-#define MPU3050_PWR_MGM_POS	6
-#define MPU3050_PWR_MGM_MASK	0x40
 
 #define MPU3050_AUTO_DELAY	1000
 
 #define MPU3050_MIN_VALUE	-32768
 #define MPU3050_MAX_VALUE	32767
 
+#define MPU3050_DEFAULT_POLL_INTERVAL	200
+#define MPU3050_DEFAULT_FS_RANGE	3
+
+/* Register map */
+#define MPU3050_CHIP_ID_REG	0x00
+#define MPU3050_SMPLRT_DIV	0x15
+#define MPU3050_DLPF_FS_SYNC	0x16
+#define MPU3050_INT_CFG		0x17
+#define MPU3050_XOUT_H		0x1D
+#define MPU3050_PWR_MGM		0x3E
+#define MPU3050_PWR_MGM_POS	6
+
+/* Register bits */
+
+/* DLPF_FS_SYNC */
+#define MPU3050_EXT_SYNC_NONE		0x00
+#define MPU3050_EXT_SYNC_TEMP		0x20
+#define MPU3050_EXT_SYNC_GYROX		0x40
+#define MPU3050_EXT_SYNC_GYROY		0x60
+#define MPU3050_EXT_SYNC_GYROZ		0x80
+#define MPU3050_EXT_SYNC_ACCELX	0xA0
+#define MPU3050_EXT_SYNC_ACCELY	0xC0
+#define MPU3050_EXT_SYNC_ACCELZ	0xE0
+#define MPU3050_EXT_SYNC_MASK		0xE0
+#define MPU3050_FS_250DPS		0x00
+#define MPU3050_FS_500DPS		0x08
+#define MPU3050_FS_1000DPS		0x10
+#define MPU3050_FS_2000DPS		0x18
+#define MPU3050_FS_MASK		0x18
+#define MPU3050_DLPF_CFG_256HZ_NOLPF2	0x00
+#define MPU3050_DLPF_CFG_188HZ		0x01
+#define MPU3050_DLPF_CFG_98HZ		0x02
+#define MPU3050_DLPF_CFG_42HZ		0x03
+#define MPU3050_DLPF_CFG_20HZ		0x04
+#define MPU3050_DLPF_CFG_10HZ		0x05
+#define MPU3050_DLPF_CFG_5HZ		0x06
+#define MPU3050_DLPF_CFG_2100HZ_NOLPF	0x07
+#define MPU3050_DLPF_CFG_MASK		0x07
+/* INT_CFG */
+#define MPU3050_RAW_RDY_EN		0x01
+#define MPU3050_MPU_RDY_EN		0x02
+#define MPU3050_LATCH_INT_EN		0x04
+/* PWR_MGM */
+#define MPU3050_PWR_MGM_PLL_X		0x01
+#define MPU3050_PWR_MGM_PLL_Y		0x02
+#define MPU3050_PWR_MGM_PLL_Z		0x03
+#define MPU3050_PWR_MGM_CLKSEL		0x07
+#define MPU3050_PWR_MGM_STBY_ZG	0x08
+#define MPU3050_PWR_MGM_STBY_YG	0x10
+#define MPU3050_PWR_MGM_STBY_XG	0x20
+#define MPU3050_PWR_MGM_SLEEP		0x40
+#define MPU3050_PWR_MGM_RESET		0x80
+#define MPU3050_PWR_MGM_MASK		0x40
+
 struct axis_data {
 	s16 x;
 	s16 y;
@@ -148,9 +197,20 @@ static void mpu3050_set_power_mode(struct i2c_client *client, u8 val)
 static int mpu3050_input_open(struct input_dev *input)
 {
 	struct mpu3050_sensor *sensor = input_get_drvdata(input);
+	int error;
 
 	pm_runtime_get(sensor->dev);
 
+	/* Enable interrupts */
+	error = i2c_smbus_write_byte_data(sensor->client, MPU3050_INT_CFG,
+					  MPU3050_LATCH_INT_EN |
+					  MPU3050_RAW_RDY_EN |
+					  MPU3050_MPU_RDY_EN);
+	if (error < 0) {
+		pm_runtime_put(sensor->dev);
+		return error;
+	}
+
 	return 0;
 }
 
@@ -191,6 +251,51 @@ static irqreturn_t mpu3050_interrupt_thread(int irq, void *data)
 	return IRQ_HANDLED;
 }
 
+/**
+ *	mpu3050_hw_init	-	initialize hardware
+ *	@sensor: the sensor
+ *
+ *	Called during device probe; configures the sampling method.
+ */
+static int __devinit mpu3050_hw_init(struct mpu3050_sensor *sensor)
+{
+	struct i2c_client *client = sensor->client;
+	int ret;
+	u8 reg;
+
+	/* Reset */
+	ret = i2c_smbus_write_byte_data(client, MPU3050_PWR_MGM,
+					MPU3050_PWR_MGM_RESET);
+	if (ret < 0)
+		return ret;
+
+	ret = i2c_smbus_read_byte_data(client, MPU3050_PWR_MGM);
+	if (ret < 0)
+		return ret;
+
+	ret &= ~MPU3050_PWR_MGM_CLKSEL;
+	ret |= MPU3050_PWR_MGM_PLL_Z;
+	ret = i2c_smbus_write_byte_data(client, MPU3050_PWR_MGM, ret);
+	if (ret < 0)
+		return ret;
+
+	/* Output frequency divider. The poll interval */
+	ret = i2c_smbus_write_byte_data(client, MPU3050_SMPLRT_DIV,
+					MPU3050_DEFAULT_POLL_INTERVAL - 1);
+	if (ret < 0)
+		return ret;
+
+	/* Set low pass filter and full scale */
+	reg = MPU3050_DEFAULT_FS_RANGE;
+	reg |= MPU3050_DLPF_CFG_42HZ << 3;
+	reg |= MPU3050_EXT_SYNC_NONE << 5;
+	ret = i2c_smbus_write_byte_data(client, MPU3050_DLPF_FS_SYNC, reg);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
 /**
  *	mpu3050_probe	-	device detection callback
  *	@client: i2c client of found device
@@ -256,10 +361,14 @@ static int __devinit mpu3050_probe(struct i2c_client *client,
 
 	pm_runtime_set_active(&client->dev);
 
+	error = mpu3050_hw_init(sensor);
+	if (error)
+		goto err_pm_set_suspended;
+
 	error = request_threaded_irq(client->irq,
 				     NULL, mpu3050_interrupt_thread,
 				     IRQF_TRIGGER_RISING,
-				     "mpu_int", sensor);
+				     "mpu3050", sensor);
 	if (error) {
 		dev_err(&client->dev,
 			"can't get IRQ %d, error %d\n", client->irq, error);
@@ -348,11 +457,18 @@ static const struct i2c_device_id mpu3050_ids[] = {
 };
 MODULE_DEVICE_TABLE(i2c, mpu3050_ids);
 
+static const struct of_device_id mpu3050_of_match[] = {
+	{ .compatible = "invn,mpu3050", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, mpu3050_of_match);
+
 static struct i2c_driver mpu3050_i2c_driver = {
 	.driver	= {
 		.name	= "mpu3050",
 		.owner	= THIS_MODULE,
 		.pm	= &mpu3050_pm,
+		.of_match_table = mpu3050_of_match,
 	},
 	.probe		= mpu3050_probe,
 	.remove		= __devexit_p(mpu3050_remove),

drivers/input/misc/pcap_keys.c

@@ -125,19 +125,7 @@ static struct platform_driver pcap_keys_device_driver = {
 		.owner	= THIS_MODULE,
 	}
 };
-
-static int __init pcap_keys_init(void)
-{
-	return platform_driver_register(&pcap_keys_device_driver);
-};
-
-static void __exit pcap_keys_exit(void)
-{
-	platform_driver_unregister(&pcap_keys_device_driver);
-};
-
-module_init(pcap_keys_init);
-module_exit(pcap_keys_exit);
+module_platform_driver(pcap_keys_device_driver);
 
 MODULE_DESCRIPTION("Motorola PCAP2 input events driver");
 MODULE_AUTHOR("Ilya Petrov <ilya.muromec@gmail.com>");

drivers/input/misc/pcf50633-input.c

@@ -113,18 +113,7 @@ static struct platform_driver pcf50633_input_driver = {
 	.probe = pcf50633_input_probe,
 	.remove = __devexit_p(pcf50633_input_remove),
 };
-
-static int __init pcf50633_input_init(void)
-{
-	return platform_driver_register(&pcf50633_input_driver);
-}
-module_init(pcf50633_input_init);
-
-static void __exit pcf50633_input_exit(void)
-{
-	platform_driver_unregister(&pcf50633_input_driver);
-}
-module_exit(pcf50633_input_exit);
+module_platform_driver(pcf50633_input_driver);
 
 MODULE_AUTHOR("Balaji Rao <balajirrao@openmoko.org>");
 MODULE_DESCRIPTION("PCF50633 input driver");

drivers/input/misc/pcspkr.c

@@ -134,17 +134,5 @@ static struct platform_driver pcspkr_platform_driver = {
 	.remove		= __devexit_p(pcspkr_remove),
 	.shutdown	= pcspkr_shutdown,
 };
+module_platform_driver(pcspkr_platform_driver);
 
-
-static int __init pcspkr_init(void)
-{
-	return platform_driver_register(&pcspkr_platform_driver);
-}
-
-static void __exit pcspkr_exit(void)
-{
-	platform_driver_unregister(&pcspkr_platform_driver);
-}
-
-module_init(pcspkr_init);
-module_exit(pcspkr_exit);

drivers/input/misc/pm8xxx-vibrator.c

@@ -277,18 +277,7 @@ static struct platform_driver pm8xxx_vib_driver = {
 		.pm	= &pm8xxx_vib_pm_ops,
 	},
 };
-
-static int __init pm8xxx_vib_init(void)
-{
-	return platform_driver_register(&pm8xxx_vib_driver);
-}
-module_init(pm8xxx_vib_init);
-
-static void __exit pm8xxx_vib_exit(void)
-{
-	platform_driver_unregister(&pm8xxx_vib_driver);
-}
-module_exit(pm8xxx_vib_exit);
+module_platform_driver(pm8xxx_vib_driver);
 
 MODULE_ALIAS("platform:pm8xxx_vib");
 MODULE_DESCRIPTION("PMIC8xxx vibrator driver based on ff-memless framework");

drivers/input/misc/pmic8xxx-pwrkey.c

@@ -213,18 +213,7 @@ static struct platform_driver pmic8xxx_pwrkey_driver = {
 		.pm	= &pm8xxx_pwr_key_pm_ops,
 	},
 };
-
-static int __init pmic8xxx_pwrkey_init(void)
-{
-	return platform_driver_register(&pmic8xxx_pwrkey_driver);
-}
-module_init(pmic8xxx_pwrkey_init);
-
-static void __exit pmic8xxx_pwrkey_exit(void)
-{
-	platform_driver_unregister(&pmic8xxx_pwrkey_driver);
-}
-module_exit(pmic8xxx_pwrkey_exit);
+module_platform_driver(pmic8xxx_pwrkey_driver);
 
 MODULE_ALIAS("platform:pmic8xxx_pwrkey");
 MODULE_DESCRIPTION("PMIC8XXX Power Key driver");

drivers/input/misc/pwm-beeper.c

@@ -180,18 +180,7 @@ static struct platform_driver pwm_beeper_driver = {
 		.pm	= PWM_BEEPER_PM_OPS,
 	},
 };
-
-static int __init pwm_beeper_init(void)
-{
-	return platform_driver_register(&pwm_beeper_driver);
-}
-module_init(pwm_beeper_init);
-
-static void __exit pwm_beeper_exit(void)
-{
-	platform_driver_unregister(&pwm_beeper_driver);
-}
-module_exit(pwm_beeper_exit);
+module_platform_driver(pwm_beeper_driver);
 
 MODULE_AUTHOR("Lars-Peter Clausen <lars@metafoo.de>");
 MODULE_DESCRIPTION("PWM beeper driver");

drivers/input/misc/rb532_button.c

@@ -100,19 +100,7 @@ static struct platform_driver rb532_button_driver = {
 		.owner = THIS_MODULE,
 	},
 };
-
-static int __init rb532_button_init(void)
-{
-	return platform_driver_register(&rb532_button_driver);
-}
-
-static void __exit rb532_button_exit(void)
-{
-	platform_driver_unregister(&rb532_button_driver);
-}
-
-module_init(rb532_button_init);
-module_exit(rb532_button_exit);
+module_platform_driver(rb532_button_driver);
 
 MODULE_AUTHOR("Phil Sutter <n0-1@freewrt.org>");
 MODULE_LICENSE("GPL");

drivers/input/misc/rotary_encoder.c

@@ -284,19 +284,7 @@ static struct platform_driver rotary_encoder_driver = {
 		.owner	= THIS_MODULE,
 	}
 };
-
-static int __init rotary_encoder_init(void)
-{
-	return platform_driver_register(&rotary_encoder_driver);
-}
-
-static void __exit rotary_encoder_exit(void)
-{
-	platform_driver_unregister(&rotary_encoder_driver);
-}
-
-module_init(rotary_encoder_init);
-module_exit(rotary_encoder_exit);
+module_platform_driver(rotary_encoder_driver);
 
 MODULE_ALIAS("platform:" DRV_NAME);
 MODULE_DESCRIPTION("GPIO rotary encoder driver");

drivers/input/misc/sgi_btns.c

@@ -164,17 +164,6 @@ static struct platform_driver sgi_buttons_driver = {
 		.owner	= THIS_MODULE,
 	},
 };
-
-static int __init sgi_buttons_init(void)
-{
-	return platform_driver_register(&sgi_buttons_driver);
-}
-
-static void __exit sgi_buttons_exit(void)
-{
-	platform_driver_unregister(&sgi_buttons_driver);
-}
+module_platform_driver(sgi_buttons_driver);
 
 MODULE_LICENSE("GPL");
-module_init(sgi_buttons_init);
-module_exit(sgi_buttons_exit);

drivers/input/misc/twl4030-pwrbutton.c

@@ -107,25 +107,14 @@ static int __exit twl4030_pwrbutton_remove(struct platform_device *pdev)
 }
 
 static struct platform_driver twl4030_pwrbutton_driver = {
+	.probe		= twl4030_pwrbutton_probe,
 	.remove		= __exit_p(twl4030_pwrbutton_remove),
 	.driver		= {
 		.name	= "twl4030_pwrbutton",
 		.owner	= THIS_MODULE,
 	},
 };
-
-static int __init twl4030_pwrbutton_init(void)
-{
-	return platform_driver_probe(&twl4030_pwrbutton_driver,
-			twl4030_pwrbutton_probe);
-}
-module_init(twl4030_pwrbutton_init);
-
-static void __exit twl4030_pwrbutton_exit(void)
-{
-	platform_driver_unregister(&twl4030_pwrbutton_driver);
-}
-module_exit(twl4030_pwrbutton_exit);
+module_platform_driver(twl4030_pwrbutton_driver);
 
 MODULE_ALIAS("platform:twl4030_pwrbutton");
 MODULE_DESCRIPTION("Triton2 Power Button");

drivers/input/misc/twl4030-vibra.c

@@ -278,21 +278,9 @@ static struct platform_driver twl4030_vibra_driver = {
 #endif
 	},
 };
-
-static int __init twl4030_vibra_init(void)
-{
-	return platform_driver_register(&twl4030_vibra_driver);
-}
-module_init(twl4030_vibra_init);
-
-static void __exit twl4030_vibra_exit(void)
-{
-	platform_driver_unregister(&twl4030_vibra_driver);
-}
-module_exit(twl4030_vibra_exit);
+module_platform_driver(twl4030_vibra_driver);
 
 MODULE_ALIAS("platform:twl4030-vibra");
-
 MODULE_DESCRIPTION("TWL4030 Vibra driver");
 MODULE_LICENSE("GPL");
 MODULE_AUTHOR("Nokia Corporation");

drivers/input/misc/twl6040-vibra.c

@@ -410,18 +410,7 @@ static struct platform_driver twl6040_vibra_driver = {
 		.pm	= &twl6040_vibra_pm_ops,
 	},
 };
-
-static int __init twl6040_vibra_init(void)
-{
-	return platform_driver_register(&twl6040_vibra_driver);
-}
-module_init(twl6040_vibra_init);
-
-static void __exit twl6040_vibra_exit(void)
-{
-	platform_driver_unregister(&twl6040_vibra_driver);
-}
-module_exit(twl6040_vibra_exit);
+module_platform_driver(twl6040_vibra_driver);
 
 MODULE_ALIAS("platform:twl6040-vibra");
 MODULE_DESCRIPTION("TWL6040 Vibra driver");

drivers/input/misc/wm831x-on.c

@@ -145,18 +145,7 @@ static struct platform_driver wm831x_on_driver = {
 		.owner	= THIS_MODULE,
 	},
 };
-
-static int __init wm831x_on_init(void)
-{
-	return platform_driver_register(&wm831x_on_driver);
-}
-module_init(wm831x_on_init);
-
-static void __exit wm831x_on_exit(void)
-{
-	platform_driver_unregister(&wm831x_on_driver);
-}
-module_exit(wm831x_on_exit);
+module_platform_driver(wm831x_on_driver);
 
 MODULE_ALIAS("platform:wm831x-on");
 MODULE_DESCRIPTION("WM831x ON pin");