diff --git a/drivers/video/fbdev/Kconfig b/drivers/video/fbdev/Kconfig
index 44a8fdbab6df..77b50579bd09 100644
--- a/drivers/video/fbdev/Kconfig
+++ b/drivers/video/fbdev/Kconfig
@@ -1659,19 +1659,6 @@ config FB_SH7760
 	  and 8, 15 or 16 bpp color; 90 degrees clockwise display rotation for
 	  panels <= 320 pixel horizontal resolution.
 
-config FB_DA8XX
-	tristate "DA8xx/OMAP-L1xx/AM335x Framebuffer support"
-	depends on FB && HAVE_CLK && HAS_IOMEM
-	depends on ARCH_DAVINCI_DA8XX || SOC_AM33XX || COMPILE_TEST
-	select FB_CFB_REV_PIXELS_IN_BYTE
-	select FB_IOMEM_HELPERS
-	select FB_MODE_HELPERS
-	select VIDEOMODE_HELPERS
-	help
-	  This is the frame buffer device driver for the TI LCD controller
-	  found on DA8xx/OMAP-L1xx/AM335x SoCs.
-	  If unsure, say N.
-
 config FB_VIRTUAL
 	tristate "Virtual Frame Buffer support (ONLY FOR TESTING!)"
 	depends on FB
diff --git a/drivers/video/fbdev/Makefile b/drivers/video/fbdev/Makefile
index 3eecd51267fa..b3d12f977c06 100644
--- a/drivers/video/fbdev/Makefile
+++ b/drivers/video/fbdev/Makefile
@@ -121,7 +121,6 @@ obj-$(CONFIG_FB_VESA)             += vesafb.o
 obj-$(CONFIG_FB_EFI)              += efifb.o
 obj-$(CONFIG_FB_VGA16)            += vga16fb.o
 obj-$(CONFIG_FB_OF)               += offb.o
-obj-$(CONFIG_FB_DA8XX)		  += da8xx-fb.o
 obj-$(CONFIG_FB_SSD1307)	  += ssd1307fb.o
 obj-$(CONFIG_FB_SIMPLE)           += simplefb.o
 
diff --git a/drivers/video/fbdev/da8xx-fb.c b/drivers/video/fbdev/da8xx-fb.c
deleted file mode 100644
index fad1e13c6332..000000000000
--- a/drivers/video/fbdev/da8xx-fb.c
+++ /dev/null
@@ -1,1665 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2008-2009 MontaVista Software Inc.
- * Copyright (C) 2008-2009 Texas Instruments Inc
- *
- * Based on the LCD driver for TI Avalanche processors written by
- * Ajay Singh and Shalom Hai.
- */
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/fb.h>
-#include <linux/dma-mapping.h>
-#include <linux/device.h>
-#include <linux/platform_device.h>
-#include <linux/uaccess.h>
-#include <linux/pm_runtime.h>
-#include <linux/interrupt.h>
-#include <linux/wait.h>
-#include <linux/clk.h>
-#include <linux/cpufreq.h>
-#include <linux/console.h>
-#include <linux/regulator/consumer.h>
-#include <linux/spinlock.h>
-#include <linux/slab.h>
-#include <linux/delay.h>
-#include <linux/lcm.h>
-#include <video/da8xx-fb.h>
-#include <asm/div64.h>
-
-#define DRIVER_NAME "da8xx_lcdc"
-
-#define LCD_VERSION_1	1
-#define LCD_VERSION_2	2
-
-/* LCD Status Register */
-#define LCD_END_OF_FRAME1		BIT(9)
-#define LCD_END_OF_FRAME0		BIT(8)
-#define LCD_PL_LOAD_DONE		BIT(6)
-#define LCD_FIFO_UNDERFLOW		BIT(5)
-#define LCD_SYNC_LOST			BIT(2)
-#define LCD_FRAME_DONE			BIT(0)
-
-/* LCD DMA Control Register */
-#define LCD_DMA_BURST_SIZE(x)		((x) << 4)
-#define LCD_DMA_BURST_1			0x0
-#define LCD_DMA_BURST_2			0x1
-#define LCD_DMA_BURST_4			0x2
-#define LCD_DMA_BURST_8			0x3
-#define LCD_DMA_BURST_16		0x4
-#define LCD_V1_END_OF_FRAME_INT_ENA	BIT(2)
-#define LCD_V2_END_OF_FRAME0_INT_ENA	BIT(8)
-#define LCD_V2_END_OF_FRAME1_INT_ENA	BIT(9)
-#define LCD_DUAL_FRAME_BUFFER_ENABLE	BIT(0)
-
-/* LCD Control Register */
-#define LCD_CLK_DIVISOR(x)		((x) << 8)
-#define LCD_RASTER_MODE			0x01
-
-/* LCD Raster Control Register */
-#define LCD_PALETTE_LOAD_MODE(x)	((x) << 20)
-#define PALETTE_AND_DATA		0x00
-#define PALETTE_ONLY			0x01
-#define DATA_ONLY			0x02
-
-#define LCD_MONO_8BIT_MODE		BIT(9)
-#define LCD_RASTER_ORDER		BIT(8)
-#define LCD_TFT_MODE			BIT(7)
-#define LCD_V1_UNDERFLOW_INT_ENA	BIT(6)
-#define LCD_V2_UNDERFLOW_INT_ENA	BIT(5)
-#define LCD_V1_PL_INT_ENA		BIT(4)
-#define LCD_V2_PL_INT_ENA		BIT(6)
-#define LCD_MONOCHROME_MODE		BIT(1)
-#define LCD_RASTER_ENABLE		BIT(0)
-#define LCD_TFT_ALT_ENABLE		BIT(23)
-#define LCD_STN_565_ENABLE		BIT(24)
-#define LCD_V2_DMA_CLK_EN		BIT(2)
-#define LCD_V2_LIDD_CLK_EN		BIT(1)
-#define LCD_V2_CORE_CLK_EN		BIT(0)
-#define LCD_V2_LPP_B10			26
-#define LCD_V2_TFT_24BPP_MODE		BIT(25)
-#define LCD_V2_TFT_24BPP_UNPACK		BIT(26)
-
-/* LCD Raster Timing 2 Register */
-#define LCD_AC_BIAS_TRANSITIONS_PER_INT(x)	((x) << 16)
-#define LCD_AC_BIAS_FREQUENCY(x)		((x) << 8)
-#define LCD_SYNC_CTRL				BIT(25)
-#define LCD_SYNC_EDGE				BIT(24)
-#define LCD_INVERT_PIXEL_CLOCK			BIT(22)
-#define LCD_INVERT_LINE_CLOCK			BIT(21)
-#define LCD_INVERT_FRAME_CLOCK			BIT(20)
-
-/* LCD Block */
-#define  LCD_PID_REG				0x0
-#define  LCD_CTRL_REG				0x4
-#define  LCD_STAT_REG				0x8
-#define  LCD_RASTER_CTRL_REG			0x28
-#define  LCD_RASTER_TIMING_0_REG		0x2C
-#define  LCD_RASTER_TIMING_1_REG		0x30
-#define  LCD_RASTER_TIMING_2_REG		0x34
-#define  LCD_DMA_CTRL_REG			0x40
-#define  LCD_DMA_FRM_BUF_BASE_ADDR_0_REG	0x44
-#define  LCD_DMA_FRM_BUF_CEILING_ADDR_0_REG	0x48
-#define  LCD_DMA_FRM_BUF_BASE_ADDR_1_REG	0x4C
-#define  LCD_DMA_FRM_BUF_CEILING_ADDR_1_REG	0x50
-
-/* Interrupt Registers available only in Version 2 */
-#define  LCD_RAW_STAT_REG			0x58
-#define  LCD_MASKED_STAT_REG			0x5c
-#define  LCD_INT_ENABLE_SET_REG			0x60
-#define  LCD_INT_ENABLE_CLR_REG			0x64
-#define  LCD_END_OF_INT_IND_REG			0x68
-
-/* Clock registers available only on Version 2 */
-#define  LCD_CLK_ENABLE_REG			0x6c
-#define  LCD_CLK_RESET_REG			0x70
-#define  LCD_CLK_MAIN_RESET			BIT(3)
-
-#define LCD_NUM_BUFFERS	2
-
-#define PALETTE_SIZE	256
-
-#define	CLK_MIN_DIV	2
-#define	CLK_MAX_DIV	255
-
-static void __iomem *da8xx_fb_reg_base;
-static unsigned int lcd_revision;
-static irq_handler_t lcdc_irq_handler;
-static wait_queue_head_t frame_done_wq;
-static int frame_done_flag;
-
-static unsigned int lcdc_read(unsigned int addr)
-{
-	return (unsigned int)__raw_readl(da8xx_fb_reg_base + (addr));
-}
-
-static void lcdc_write(unsigned int val, unsigned int addr)
-{
-	__raw_writel(val, da8xx_fb_reg_base + (addr));
-}
-
-struct da8xx_fb_par {
-	struct device		*dev;
-	dma_addr_t		p_palette_base;
-	unsigned char *v_palette_base;
-	dma_addr_t		vram_phys;
-	unsigned long		vram_size;
-	void			*vram_virt;
-	unsigned int		dma_start;
-	unsigned int		dma_end;
-	struct clk *lcdc_clk;
-	int irq;
-	unsigned int palette_sz;
-	int blank;
-	wait_queue_head_t	vsync_wait;
-	int			vsync_flag;
-	int			vsync_timeout;
-	spinlock_t		lock_for_chan_update;
-
-	/*
-	 * LCDC has 2 ping pong DMA channels, channel 0
-	 * and channel 1.
-	 */
-	unsigned int		which_dma_channel_done;
-#ifdef CONFIG_CPU_FREQ
-	struct notifier_block	freq_transition;
-#endif
-	unsigned int		lcdc_clk_rate;
-	struct regulator	*lcd_supply;
-	u32 pseudo_palette[16];
-	struct fb_videomode	mode;
-	struct lcd_ctrl_config	cfg;
-};
-
-static struct fb_var_screeninfo da8xx_fb_var;
-
-static struct fb_fix_screeninfo da8xx_fb_fix = {
-	.id = "DA8xx FB Drv",
-	.type = FB_TYPE_PACKED_PIXELS,
-	.type_aux = 0,
-	.visual = FB_VISUAL_PSEUDOCOLOR,
-	.xpanstep = 0,
-	.ypanstep = 1,
-	.ywrapstep = 0,
-	.accel = FB_ACCEL_NONE
-};
-
-static struct fb_videomode known_lcd_panels[] = {
-	/* Sharp LCD035Q3DG01 */
-	[0] = {
-		.name           = "Sharp_LCD035Q3DG01",
-		.xres           = 320,
-		.yres           = 240,
-		.pixclock       = KHZ2PICOS(4607),
-		.left_margin    = 6,
-		.right_margin   = 8,
-		.upper_margin   = 2,
-		.lower_margin   = 2,
-		.hsync_len      = 0,
-		.vsync_len      = 0,
-		.sync           = FB_SYNC_CLK_INVERT,
-	},
-	/* Sharp LK043T1DG01 */
-	[1] = {
-		.name           = "Sharp_LK043T1DG01",
-		.xres           = 480,
-		.yres           = 272,
-		.pixclock       = KHZ2PICOS(7833),
-		.left_margin    = 2,
-		.right_margin   = 2,
-		.upper_margin   = 2,
-		.lower_margin   = 2,
-		.hsync_len      = 41,
-		.vsync_len      = 10,
-		.sync           = 0,
-		.flag           = 0,
-	},
-	[2] = {
-		/* Hitachi SP10Q010 */
-		.name           = "SP10Q010",
-		.xres           = 320,
-		.yres           = 240,
-		.pixclock       = KHZ2PICOS(7833),
-		.left_margin    = 10,
-		.right_margin   = 10,
-		.upper_margin   = 10,
-		.lower_margin   = 10,
-		.hsync_len      = 10,
-		.vsync_len      = 10,
-		.sync           = 0,
-		.flag           = 0,
-	},
-	[3] = {
-		/* Densitron 84-0023-001T */
-		.name           = "Densitron_84-0023-001T",
-		.xres           = 320,
-		.yres           = 240,
-		.pixclock       = KHZ2PICOS(6400),
-		.left_margin    = 0,
-		.right_margin   = 0,
-		.upper_margin   = 0,
-		.lower_margin   = 0,
-		.hsync_len      = 30,
-		.vsync_len      = 3,
-		.sync           = 0,
-	},
-};
-
-static bool da8xx_fb_is_raster_enabled(void)
-{
-	return !!(lcdc_read(LCD_RASTER_CTRL_REG) & LCD_RASTER_ENABLE);
-}
-
-/* Enable the Raster Engine of the LCD Controller */
-static void lcd_enable_raster(void)
-{
-	u32 reg;
-
-	/* Put LCDC in reset for several cycles */
-	if (lcd_revision == LCD_VERSION_2)
-		/* Write 1 to reset LCDC */
-		lcdc_write(LCD_CLK_MAIN_RESET, LCD_CLK_RESET_REG);
-	mdelay(1);
-
-	/* Bring LCDC out of reset */
-	if (lcd_revision == LCD_VERSION_2)
-		lcdc_write(0, LCD_CLK_RESET_REG);
-	mdelay(1);
-
-	/* Above reset sequence doesnot reset register context */
-	reg = lcdc_read(LCD_RASTER_CTRL_REG);
-	if (!(reg & LCD_RASTER_ENABLE))
-		lcdc_write(reg | LCD_RASTER_ENABLE, LCD_RASTER_CTRL_REG);
-}
-
-/* Disable the Raster Engine of the LCD Controller */
-static void lcd_disable_raster(enum da8xx_frame_complete wait_for_frame_done)
-{
-	u32 reg;
-	int ret;
-
-	reg = lcdc_read(LCD_RASTER_CTRL_REG);
-	if (reg & LCD_RASTER_ENABLE)
-		lcdc_write(reg & ~LCD_RASTER_ENABLE, LCD_RASTER_CTRL_REG);
-	else
-		/* return if already disabled */
-		return;
-
-	if ((wait_for_frame_done == DA8XX_FRAME_WAIT) &&
-			(lcd_revision == LCD_VERSION_2)) {
-		frame_done_flag = 0;
-		ret = wait_event_interruptible_timeout(frame_done_wq,
-				frame_done_flag != 0,
-				msecs_to_jiffies(50));
-		if (ret == 0)
-			pr_err("LCD Controller timed out\n");
-	}
-}
-
-static void lcd_blit(int load_mode, struct da8xx_fb_par *par)
-{
-	u32 start;
-	u32 end;
-	u32 reg_ras;
-	u32 reg_dma;
-	u32 reg_int;
-
-	/* init reg to clear PLM (loading mode) fields */
-	reg_ras = lcdc_read(LCD_RASTER_CTRL_REG);
-	reg_ras &= ~(3 << 20);
-
-	reg_dma  = lcdc_read(LCD_DMA_CTRL_REG);
-
-	if (load_mode == LOAD_DATA) {
-		start    = par->dma_start;
-		end      = par->dma_end;
-
-		reg_ras |= LCD_PALETTE_LOAD_MODE(DATA_ONLY);
-		if (lcd_revision == LCD_VERSION_1) {
-			reg_dma |= LCD_V1_END_OF_FRAME_INT_ENA;
-		} else {
-			reg_int = lcdc_read(LCD_INT_ENABLE_SET_REG) |
-				LCD_V2_END_OF_FRAME0_INT_ENA |
-				LCD_V2_END_OF_FRAME1_INT_ENA |
-				LCD_FRAME_DONE | LCD_SYNC_LOST;
-			lcdc_write(reg_int, LCD_INT_ENABLE_SET_REG);
-		}
-		reg_dma |= LCD_DUAL_FRAME_BUFFER_ENABLE;
-
-		lcdc_write(start, LCD_DMA_FRM_BUF_BASE_ADDR_0_REG);
-		lcdc_write(end, LCD_DMA_FRM_BUF_CEILING_ADDR_0_REG);
-		lcdc_write(start, LCD_DMA_FRM_BUF_BASE_ADDR_1_REG);
-		lcdc_write(end, LCD_DMA_FRM_BUF_CEILING_ADDR_1_REG);
-	} else if (load_mode == LOAD_PALETTE) {
-		start    = par->p_palette_base;
-		end      = start + par->palette_sz - 1;
-
-		reg_ras |= LCD_PALETTE_LOAD_MODE(PALETTE_ONLY);
-
-		if (lcd_revision == LCD_VERSION_1) {
-			reg_ras |= LCD_V1_PL_INT_ENA;
-		} else {
-			reg_int = lcdc_read(LCD_INT_ENABLE_SET_REG) |
-				LCD_V2_PL_INT_ENA;
-			lcdc_write(reg_int, LCD_INT_ENABLE_SET_REG);
-		}
-
-		lcdc_write(start, LCD_DMA_FRM_BUF_BASE_ADDR_0_REG);
-		lcdc_write(end, LCD_DMA_FRM_BUF_CEILING_ADDR_0_REG);
-	}
-
-	lcdc_write(reg_dma, LCD_DMA_CTRL_REG);
-	lcdc_write(reg_ras, LCD_RASTER_CTRL_REG);
-
-	/*
-	 * The Raster enable bit must be set after all other control fields are
-	 * set.
-	 */
-	lcd_enable_raster();
-}
-
-/* Configure the Burst Size and fifo threhold of DMA */
-static int lcd_cfg_dma(int burst_size, int fifo_th)
-{
-	u32 reg;
-
-	reg = lcdc_read(LCD_DMA_CTRL_REG) & 0x00000001;
-	switch (burst_size) {
-	case 1:
-		reg |= LCD_DMA_BURST_SIZE(LCD_DMA_BURST_1);
-		break;
-	case 2:
-		reg |= LCD_DMA_BURST_SIZE(LCD_DMA_BURST_2);
-		break;
-	case 4:
-		reg |= LCD_DMA_BURST_SIZE(LCD_DMA_BURST_4);
-		break;
-	case 8:
-		reg |= LCD_DMA_BURST_SIZE(LCD_DMA_BURST_8);
-		break;
-	case 16:
-	default:
-		reg |= LCD_DMA_BURST_SIZE(LCD_DMA_BURST_16);
-		break;
-	}
-
-	reg |= (fifo_th << 8);
-
-	lcdc_write(reg, LCD_DMA_CTRL_REG);
-
-	return 0;
-}
-
-static void lcd_cfg_ac_bias(int period, int transitions_per_int)
-{
-	u32 reg;
-
-	/* Set the AC Bias Period and Number of Transisitons per Interrupt */
-	reg = lcdc_read(LCD_RASTER_TIMING_2_REG) & 0xFFF00000;
-	reg |= LCD_AC_BIAS_FREQUENCY(period) |
-		LCD_AC_BIAS_TRANSITIONS_PER_INT(transitions_per_int);
-	lcdc_write(reg, LCD_RASTER_TIMING_2_REG);
-}
-
-static void lcd_cfg_horizontal_sync(int back_porch, int pulse_width,
-		int front_porch)
-{
-	u32 reg;
-
-	reg = lcdc_read(LCD_RASTER_TIMING_0_REG) & 0x3ff;
-	reg |= (((back_porch-1) & 0xff) << 24)
-	    | (((front_porch-1) & 0xff) << 16)
-	    | (((pulse_width-1) & 0x3f) << 10);
-	lcdc_write(reg, LCD_RASTER_TIMING_0_REG);
-
-	/*
-	 * LCDC Version 2 adds some extra bits that increase the allowable
-	 * size of the horizontal timing registers.
-	 * remember that the registers use 0 to represent 1 so all values
-	 * that get set into register need to be decremented by 1
-	 */
-	if (lcd_revision == LCD_VERSION_2) {
-		/* Mask off the bits we want to change */
-		reg = lcdc_read(LCD_RASTER_TIMING_2_REG) & ~0x780000ff;
-		reg |= ((front_porch-1) & 0x300) >> 8;
-		reg |= ((back_porch-1) & 0x300) >> 4;
-		reg |= ((pulse_width-1) & 0x3c0) << 21;
-		lcdc_write(reg, LCD_RASTER_TIMING_2_REG);
-	}
-}
-
-static void lcd_cfg_vertical_sync(int back_porch, int pulse_width,
-		int front_porch)
-{
-	u32 reg;
-
-	reg = lcdc_read(LCD_RASTER_TIMING_1_REG) & 0x3ff;
-	reg |= ((back_porch & 0xff) << 24)
-	    | ((front_porch & 0xff) << 16)
-	    | (((pulse_width-1) & 0x3f) << 10);
-	lcdc_write(reg, LCD_RASTER_TIMING_1_REG);
-}
-
-static int lcd_cfg_display(const struct lcd_ctrl_config *cfg,
-		struct fb_videomode *panel)
-{
-	u32 reg;
-	u32 reg_int;
-
-	reg = lcdc_read(LCD_RASTER_CTRL_REG) & ~(LCD_TFT_MODE |
-						LCD_MONO_8BIT_MODE |
-						LCD_MONOCHROME_MODE);
-
-	switch (cfg->panel_shade) {
-	case MONOCHROME:
-		reg |= LCD_MONOCHROME_MODE;
-		if (cfg->mono_8bit_mode)
-			reg |= LCD_MONO_8BIT_MODE;
-		break;
-	case COLOR_ACTIVE:
-		reg |= LCD_TFT_MODE;
-		if (cfg->tft_alt_mode)
-			reg |= LCD_TFT_ALT_ENABLE;
-		break;
-
-	case COLOR_PASSIVE:
-		/* AC bias applicable only for Pasive panels */
-		lcd_cfg_ac_bias(cfg->ac_bias, cfg->ac_bias_intrpt);
-		if (cfg->bpp == 12 && cfg->stn_565_mode)
-			reg |= LCD_STN_565_ENABLE;
-		break;
-
-	default:
-		return -EINVAL;
-	}
-
-	/* enable additional interrupts here */
-	if (lcd_revision == LCD_VERSION_1) {
-		reg |= LCD_V1_UNDERFLOW_INT_ENA;
-	} else {
-		reg_int = lcdc_read(LCD_INT_ENABLE_SET_REG) |
-			LCD_V2_UNDERFLOW_INT_ENA;
-		lcdc_write(reg_int, LCD_INT_ENABLE_SET_REG);
-	}
-
-	lcdc_write(reg, LCD_RASTER_CTRL_REG);
-
-	reg = lcdc_read(LCD_RASTER_TIMING_2_REG);
-
-	reg |= LCD_SYNC_CTRL;
-
-	if (cfg->sync_edge)
-		reg |= LCD_SYNC_EDGE;
-	else
-		reg &= ~LCD_SYNC_EDGE;
-
-	if ((panel->sync & FB_SYNC_HOR_HIGH_ACT) == 0)
-		reg |= LCD_INVERT_LINE_CLOCK;
-	else
-		reg &= ~LCD_INVERT_LINE_CLOCK;
-
-	if ((panel->sync & FB_SYNC_VERT_HIGH_ACT) == 0)
-		reg |= LCD_INVERT_FRAME_CLOCK;
-	else
-		reg &= ~LCD_INVERT_FRAME_CLOCK;
-
-	lcdc_write(reg, LCD_RASTER_TIMING_2_REG);
-
-	return 0;
-}
-
-static int lcd_cfg_frame_buffer(struct da8xx_fb_par *par, u32 width, u32 height,
-		u32 bpp, u32 raster_order)
-{
-	u32 reg;
-
-	if (bpp > 16 && lcd_revision == LCD_VERSION_1)
-		return -EINVAL;
-
-	/* Set the Panel Width */
-	/* Pixels per line = (PPL + 1)*16 */
-	if (lcd_revision == LCD_VERSION_1) {
-		/*
-		 * 0x3F in bits 4..9 gives max horizontal resolution = 1024
-		 * pixels.
-		 */
-		width &= 0x3f0;
-	} else {
-		/*
-		 * 0x7F in bits 4..10 gives max horizontal resolution = 2048
-		 * pixels.
-		 */
-		width &= 0x7f0;
-	}
-
-	reg = lcdc_read(LCD_RASTER_TIMING_0_REG);
-	reg &= 0xfffffc00;
-	if (lcd_revision == LCD_VERSION_1) {
-		reg |= ((width >> 4) - 1) << 4;
-	} else {
-		width = (width >> 4) - 1;
-		reg |= ((width & 0x3f) << 4) | ((width & 0x40) >> 3);
-	}
-	lcdc_write(reg, LCD_RASTER_TIMING_0_REG);
-
-	/* Set the Panel Height */
-	/* Set bits 9:0 of Lines Per Pixel */
-	reg = lcdc_read(LCD_RASTER_TIMING_1_REG);
-	reg = ((height - 1) & 0x3ff) | (reg & 0xfffffc00);
-	lcdc_write(reg, LCD_RASTER_TIMING_1_REG);
-
-	/* Set bit 10 of Lines Per Pixel */
-	if (lcd_revision == LCD_VERSION_2) {
-		reg = lcdc_read(LCD_RASTER_TIMING_2_REG);
-		reg |= ((height - 1) & 0x400) << 16;
-		lcdc_write(reg, LCD_RASTER_TIMING_2_REG);
-	}
-
-	/* Set the Raster Order of the Frame Buffer */
-	reg = lcdc_read(LCD_RASTER_CTRL_REG) & ~(1 << 8);
-	if (raster_order)
-		reg |= LCD_RASTER_ORDER;
-
-	par->palette_sz = 16 * 2;
-
-	switch (bpp) {
-	case 1:
-	case 2:
-	case 4:
-	case 16:
-		break;
-	case 24:
-		reg |= LCD_V2_TFT_24BPP_MODE;
-		break;
-	case 32:
-		reg |= LCD_V2_TFT_24BPP_MODE;
-		reg |= LCD_V2_TFT_24BPP_UNPACK;
-		break;
-	case 8:
-		par->palette_sz = 256 * 2;
-		break;
-
-	default:
-		return -EINVAL;
-	}
-
-	lcdc_write(reg, LCD_RASTER_CTRL_REG);
-
-	return 0;
-}
-
-#define CNVT_TOHW(val, width) ((((val) << (width)) + 0x7FFF - (val)) >> 16)
-static int fb_setcolreg(unsigned regno, unsigned red, unsigned green,
-			      unsigned blue, unsigned transp,
-			      struct fb_info *info)
-{
-	struct da8xx_fb_par *par = info->par;
-	unsigned short *palette = (unsigned short *) par->v_palette_base;
-	u_short pal;
-	int update_hw = 0;
-
-	if (regno > 255)
-		return 1;
-
-	if (info->fix.visual == FB_VISUAL_DIRECTCOLOR)
-		return 1;
-
-	if (info->var.bits_per_pixel > 16 && lcd_revision == LCD_VERSION_1)
-		return -EINVAL;
-
-	switch (info->fix.visual) {
-	case FB_VISUAL_TRUECOLOR:
-		red = CNVT_TOHW(red, info->var.red.length);
-		green = CNVT_TOHW(green, info->var.green.length);
-		blue = CNVT_TOHW(blue, info->var.blue.length);
-		break;
-	case FB_VISUAL_PSEUDOCOLOR:
-		switch (info->var.bits_per_pixel) {
-		case 4:
-			if (regno > 15)
-				return -EINVAL;
-
-			if (info->var.grayscale) {
-				pal = regno;
-			} else {
-				red >>= 4;
-				green >>= 8;
-				blue >>= 12;
-
-				pal = red & 0x0f00;
-				pal |= green & 0x00f0;
-				pal |= blue & 0x000f;
-			}
-			if (regno == 0)
-				pal |= 0x2000;
-			palette[regno] = pal;
-			break;
-
-		case 8:
-			red >>= 4;
-			green >>= 8;
-			blue >>= 12;
-
-			pal = (red & 0x0f00);
-			pal |= (green & 0x00f0);
-			pal |= (blue & 0x000f);
-
-			if (palette[regno] != pal) {
-				update_hw = 1;
-				palette[regno] = pal;
-			}
-			break;
-		}
-		break;
-	}
-
-	/* Truecolor has hardware independent palette */
-	if (info->fix.visual == FB_VISUAL_TRUECOLOR) {
-		u32 v;
-
-		if (regno > 15)
-			return -EINVAL;
-
-		v = (red << info->var.red.offset) |
-			(green << info->var.green.offset) |
-			(blue << info->var.blue.offset);
-
-		((u32 *) (info->pseudo_palette))[regno] = v;
-		if (palette[0] != 0x4000) {
-			update_hw = 1;
-			palette[0] = 0x4000;
-		}
-	}
-
-	/* Update the palette in the h/w as needed. */
-	if (update_hw)
-		lcd_blit(LOAD_PALETTE, par);
-
-	return 0;
-}
-#undef CNVT_TOHW
-
-static void da8xx_fb_lcd_reset(void)
-{
-	/* DMA has to be disabled */
-	lcdc_write(0, LCD_DMA_CTRL_REG);
-	lcdc_write(0, LCD_RASTER_CTRL_REG);
-
-	if (lcd_revision == LCD_VERSION_2) {
-		lcdc_write(0, LCD_INT_ENABLE_SET_REG);
-		/* Write 1 to reset */
-		lcdc_write(LCD_CLK_MAIN_RESET, LCD_CLK_RESET_REG);
-		lcdc_write(0, LCD_CLK_RESET_REG);
-	}
-}
-
-static int da8xx_fb_config_clk_divider(struct da8xx_fb_par *par,
-					      unsigned lcdc_clk_div,
-					      unsigned lcdc_clk_rate)
-{
-	int ret;
-
-	if (par->lcdc_clk_rate != lcdc_clk_rate) {
-		ret = clk_set_rate(par->lcdc_clk, lcdc_clk_rate);
-		if (ret) {
-			dev_err(par->dev,
-				"unable to set clock rate at %u\n",
-				lcdc_clk_rate);
-			return ret;
-		}
-		par->lcdc_clk_rate = clk_get_rate(par->lcdc_clk);
-	}
-
-	/* Configure the LCD clock divisor. */
-	lcdc_write(LCD_CLK_DIVISOR(lcdc_clk_div) |
-			(LCD_RASTER_MODE & 0x1), LCD_CTRL_REG);
-
-	if (lcd_revision == LCD_VERSION_2)
-		lcdc_write(LCD_V2_DMA_CLK_EN | LCD_V2_LIDD_CLK_EN |
-				LCD_V2_CORE_CLK_EN, LCD_CLK_ENABLE_REG);
-
-	return 0;
-}
-
-static unsigned int da8xx_fb_calc_clk_divider(struct da8xx_fb_par *par,
-					      unsigned pixclock,
-					      unsigned *lcdc_clk_rate)
-{
-	unsigned lcdc_clk_div;
-
-	pixclock = PICOS2KHZ(pixclock) * 1000;
-
-	*lcdc_clk_rate = par->lcdc_clk_rate;
-
-	if (pixclock < (*lcdc_clk_rate / CLK_MAX_DIV)) {
-		*lcdc_clk_rate = clk_round_rate(par->lcdc_clk,
-						pixclock * CLK_MAX_DIV);
-		lcdc_clk_div = CLK_MAX_DIV;
-	} else if (pixclock > (*lcdc_clk_rate / CLK_MIN_DIV)) {
-		*lcdc_clk_rate = clk_round_rate(par->lcdc_clk,
-						pixclock * CLK_MIN_DIV);
-		lcdc_clk_div = CLK_MIN_DIV;
-	} else {
-		lcdc_clk_div = *lcdc_clk_rate / pixclock;
-	}
-
-	return lcdc_clk_div;
-}
-
-static int da8xx_fb_calc_config_clk_divider(struct da8xx_fb_par *par,
-					    struct fb_videomode *mode)
-{
-	unsigned lcdc_clk_rate;
-	unsigned lcdc_clk_div = da8xx_fb_calc_clk_divider(par, mode->pixclock,
-							  &lcdc_clk_rate);
-
-	return da8xx_fb_config_clk_divider(par, lcdc_clk_div, lcdc_clk_rate);
-}
-
-static unsigned da8xx_fb_round_clk(struct da8xx_fb_par *par,
-					  unsigned pixclock)
-{
-	unsigned lcdc_clk_div, lcdc_clk_rate;
-
-	lcdc_clk_div = da8xx_fb_calc_clk_divider(par, pixclock, &lcdc_clk_rate);
-	return KHZ2PICOS(lcdc_clk_rate / (1000 * lcdc_clk_div));
-}
-
-static int lcd_init(struct da8xx_fb_par *par, const struct lcd_ctrl_config *cfg,
-		struct fb_videomode *panel)
-{
-	u32 bpp;
-	int ret = 0;
-
-	ret = da8xx_fb_calc_config_clk_divider(par, panel);
-	if (ret) {
-		dev_err(par->dev, "unable to configure clock\n");
-		return ret;
-	}
-
-	if (panel->sync & FB_SYNC_CLK_INVERT)
-		lcdc_write((lcdc_read(LCD_RASTER_TIMING_2_REG) |
-			LCD_INVERT_PIXEL_CLOCK), LCD_RASTER_TIMING_2_REG);
-	else
-		lcdc_write((lcdc_read(LCD_RASTER_TIMING_2_REG) &
-			~LCD_INVERT_PIXEL_CLOCK), LCD_RASTER_TIMING_2_REG);
-
-	/* Configure the DMA burst size and fifo threshold. */
-	ret = lcd_cfg_dma(cfg->dma_burst_sz, cfg->fifo_th);
-	if (ret < 0)
-		return ret;
-
-	/* Configure the vertical and horizontal sync properties. */
-	lcd_cfg_vertical_sync(panel->upper_margin, panel->vsync_len,
-			panel->lower_margin);
-	lcd_cfg_horizontal_sync(panel->left_margin, panel->hsync_len,
-			panel->right_margin);
-
-	/* Configure for disply */
-	ret = lcd_cfg_display(cfg, panel);
-	if (ret < 0)
-		return ret;
-
-	bpp = cfg->bpp;
-
-	if (bpp == 12)
-		bpp = 16;
-	ret = lcd_cfg_frame_buffer(par, (unsigned int)panel->xres,
-				(unsigned int)panel->yres, bpp,
-				cfg->raster_order);
-	if (ret < 0)
-		return ret;
-
-	/* Configure FDD */
-	lcdc_write((lcdc_read(LCD_RASTER_CTRL_REG) & 0xfff00fff) |
-		       (cfg->fdd << 12), LCD_RASTER_CTRL_REG);
-
-	return 0;
-}
-
-/* IRQ handler for version 2 of LCDC */
-static irqreturn_t lcdc_irq_handler_rev02(int irq, void *arg)
-{
-	struct da8xx_fb_par *par = arg;
-	u32 stat = lcdc_read(LCD_MASKED_STAT_REG);
-
-	if ((stat & LCD_SYNC_LOST) && (stat & LCD_FIFO_UNDERFLOW)) {
-		lcd_disable_raster(DA8XX_FRAME_NOWAIT);
-		lcdc_write(stat, LCD_MASKED_STAT_REG);
-		lcd_enable_raster();
-	} else if (stat & LCD_PL_LOAD_DONE) {
-		/*
-		 * Must disable raster before changing state of any control bit.
-		 * And also must be disabled before clearing the PL loading
-		 * interrupt via the following write to the status register. If
-		 * this is done after then one gets multiple PL done interrupts.
-		 */
-		lcd_disable_raster(DA8XX_FRAME_NOWAIT);
-
-		lcdc_write(stat, LCD_MASKED_STAT_REG);
-
-		/* Disable PL completion interrupt */
-		lcdc_write(LCD_V2_PL_INT_ENA, LCD_INT_ENABLE_CLR_REG);
-
-		/* Setup and start data loading mode */
-		lcd_blit(LOAD_DATA, par);
-	} else {
-		lcdc_write(stat, LCD_MASKED_STAT_REG);
-
-		if (stat & LCD_END_OF_FRAME0) {
-			par->which_dma_channel_done = 0;
-			lcdc_write(par->dma_start,
-				   LCD_DMA_FRM_BUF_BASE_ADDR_0_REG);
-			lcdc_write(par->dma_end,
-				   LCD_DMA_FRM_BUF_CEILING_ADDR_0_REG);
-			par->vsync_flag = 1;
-			wake_up_interruptible(&par->vsync_wait);
-		}
-
-		if (stat & LCD_END_OF_FRAME1) {
-			par->which_dma_channel_done = 1;
-			lcdc_write(par->dma_start,
-				   LCD_DMA_FRM_BUF_BASE_ADDR_1_REG);
-			lcdc_write(par->dma_end,
-				   LCD_DMA_FRM_BUF_CEILING_ADDR_1_REG);
-			par->vsync_flag = 1;
-			wake_up_interruptible(&par->vsync_wait);
-		}
-
-		/* Set only when controller is disabled and at the end of
-		 * active frame
-		 */
-		if (stat & BIT(0)) {
-			frame_done_flag = 1;
-			wake_up_interruptible(&frame_done_wq);
-		}
-	}
-
-	lcdc_write(0, LCD_END_OF_INT_IND_REG);
-	return IRQ_HANDLED;
-}
-
-/* IRQ handler for version 1 LCDC */
-static irqreturn_t lcdc_irq_handler_rev01(int irq, void *arg)
-{
-	struct da8xx_fb_par *par = arg;
-	u32 stat = lcdc_read(LCD_STAT_REG);
-	u32 reg_ras;
-
-	if ((stat & LCD_SYNC_LOST) && (stat & LCD_FIFO_UNDERFLOW)) {
-		lcd_disable_raster(DA8XX_FRAME_NOWAIT);
-		lcdc_write(stat, LCD_STAT_REG);
-		lcd_enable_raster();
-	} else if (stat & LCD_PL_LOAD_DONE) {
-		/*
-		 * Must disable raster before changing state of any control bit.
-		 * And also must be disabled before clearing the PL loading
-		 * interrupt via the following write to the status register. If
-		 * this is done after then one gets multiple PL done interrupts.
-		 */
-		lcd_disable_raster(DA8XX_FRAME_NOWAIT);
-
-		lcdc_write(stat, LCD_STAT_REG);
-
-		/* Disable PL completion inerrupt */
-		reg_ras  = lcdc_read(LCD_RASTER_CTRL_REG);
-		reg_ras &= ~LCD_V1_PL_INT_ENA;
-		lcdc_write(reg_ras, LCD_RASTER_CTRL_REG);
-
-		/* Setup and start data loading mode */
-		lcd_blit(LOAD_DATA, par);
-	} else {
-		lcdc_write(stat, LCD_STAT_REG);
-
-		if (stat & LCD_END_OF_FRAME0) {
-			par->which_dma_channel_done = 0;
-			lcdc_write(par->dma_start,
-				   LCD_DMA_FRM_BUF_BASE_ADDR_0_REG);
-			lcdc_write(par->dma_end,
-				   LCD_DMA_FRM_BUF_CEILING_ADDR_0_REG);
-			par->vsync_flag = 1;
-			wake_up_interruptible(&par->vsync_wait);
-		}
-
-		if (stat & LCD_END_OF_FRAME1) {
-			par->which_dma_channel_done = 1;
-			lcdc_write(par->dma_start,
-				   LCD_DMA_FRM_BUF_BASE_ADDR_1_REG);
-			lcdc_write(par->dma_end,
-				   LCD_DMA_FRM_BUF_CEILING_ADDR_1_REG);
-			par->vsync_flag = 1;
-			wake_up_interruptible(&par->vsync_wait);
-		}
-	}
-
-	return IRQ_HANDLED;
-}
-
-static int fb_check_var(struct fb_var_screeninfo *var,
-			struct fb_info *info)
-{
-	int err = 0;
-	struct da8xx_fb_par *par = info->par;
-	int bpp = var->bits_per_pixel >> 3;
-	unsigned long line_size = var->xres_virtual * bpp;
-
-	if (var->bits_per_pixel > 16 && lcd_revision == LCD_VERSION_1)
-		return -EINVAL;
-
-	switch (var->bits_per_pixel) {
-	case 1:
-	case 8:
-		var->red.offset = 0;
-		var->red.length = 8;
-		var->green.offset = 0;
-		var->green.length = 8;
-		var->blue.offset = 0;
-		var->blue.length = 8;
-		var->transp.offset = 0;
-		var->transp.length = 0;
-		var->nonstd = 0;
-		break;
-	case 4:
-		var->red.offset = 0;
-		var->red.length = 4;
-		var->green.offset = 0;
-		var->green.length = 4;
-		var->blue.offset = 0;
-		var->blue.length = 4;
-		var->transp.offset = 0;
-		var->transp.length = 0;
-		var->nonstd = FB_NONSTD_REV_PIX_IN_B;
-		break;
-	case 16:		/* RGB 565 */
-		var->red.offset = 11;
-		var->red.length = 5;
-		var->green.offset = 5;
-		var->green.length = 6;
-		var->blue.offset = 0;
-		var->blue.length = 5;
-		var->transp.offset = 0;
-		var->transp.length = 0;
-		var->nonstd = 0;
-		break;
-	case 24:
-		var->red.offset = 16;
-		var->red.length = 8;
-		var->green.offset = 8;
-		var->green.length = 8;
-		var->blue.offset = 0;
-		var->blue.length = 8;
-		var->nonstd = 0;
-		break;
-	case 32:
-		var->transp.offset = 24;
-		var->transp.length = 8;
-		var->red.offset = 16;
-		var->red.length = 8;
-		var->green.offset = 8;
-		var->green.length = 8;
-		var->blue.offset = 0;
-		var->blue.length = 8;
-		var->nonstd = 0;
-		break;
-	default:
-		err = -EINVAL;
-	}
-
-	var->red.msb_right = 0;
-	var->green.msb_right = 0;
-	var->blue.msb_right = 0;
-	var->transp.msb_right = 0;
-
-	if (line_size * var->yres_virtual > par->vram_size)
-		var->yres_virtual = par->vram_size / line_size;
-
-	if (var->yres > var->yres_virtual)
-		var->yres = var->yres_virtual;
-
-	if (var->xres > var->xres_virtual)
-		var->xres = var->xres_virtual;
-
-	if (var->xres + var->xoffset > var->xres_virtual)
-		var->xoffset = var->xres_virtual - var->xres;
-	if (var->yres + var->yoffset > var->yres_virtual)
-		var->yoffset = var->yres_virtual - var->yres;
-
-	var->pixclock = da8xx_fb_round_clk(par, var->pixclock);
-
-	return err;
-}
-
-#ifdef CONFIG_CPU_FREQ
-static int lcd_da8xx_cpufreq_transition(struct notifier_block *nb,
-				     unsigned long val, void *data)
-{
-	struct da8xx_fb_par *par;
-
-	par = container_of(nb, struct da8xx_fb_par, freq_transition);
-	if (val == CPUFREQ_POSTCHANGE) {
-		if (par->lcdc_clk_rate != clk_get_rate(par->lcdc_clk)) {
-			par->lcdc_clk_rate = clk_get_rate(par->lcdc_clk);
-			lcd_disable_raster(DA8XX_FRAME_WAIT);
-			da8xx_fb_calc_config_clk_divider(par, &par->mode);
-			if (par->blank == FB_BLANK_UNBLANK)
-				lcd_enable_raster();
-		}
-	}
-
-	return 0;
-}
-
-static int lcd_da8xx_cpufreq_register(struct da8xx_fb_par *par)
-{
-	par->freq_transition.notifier_call = lcd_da8xx_cpufreq_transition;
-
-	return cpufreq_register_notifier(&par->freq_transition,
-					 CPUFREQ_TRANSITION_NOTIFIER);
-}
-
-static void lcd_da8xx_cpufreq_deregister(struct da8xx_fb_par *par)
-{
-	cpufreq_unregister_notifier(&par->freq_transition,
-				    CPUFREQ_TRANSITION_NOTIFIER);
-}
-#endif
-
-static void fb_remove(struct platform_device *dev)
-{
-	struct fb_info *info = platform_get_drvdata(dev);
-	struct da8xx_fb_par *par = info->par;
-	int ret;
-
-#ifdef CONFIG_CPU_FREQ
-	lcd_da8xx_cpufreq_deregister(par);
-#endif
-	if (par->lcd_supply) {
-		ret = regulator_disable(par->lcd_supply);
-		if (ret)
-			dev_warn(&dev->dev, "Failed to disable regulator (%pe)\n",
-				 ERR_PTR(ret));
-	}
-
-	lcd_disable_raster(DA8XX_FRAME_WAIT);
-	lcdc_write(0, LCD_RASTER_CTRL_REG);
-
-	/* disable DMA  */
-	lcdc_write(0, LCD_DMA_CTRL_REG);
-
-	unregister_framebuffer(info);
-	fb_dealloc_cmap(&info->cmap);
-	pm_runtime_put_sync(&dev->dev);
-	pm_runtime_disable(&dev->dev);
-	framebuffer_release(info);
-}
-
-/*
- * Function to wait for vertical sync which for this LCD peripheral
- * translates into waiting for the current raster frame to complete.
- */
-static int fb_wait_for_vsync(struct fb_info *info)
-{
-	struct da8xx_fb_par *par = info->par;
-	int ret;
-
-	/*
-	 * Set flag to 0 and wait for isr to set to 1. It would seem there is a
-	 * race condition here where the ISR could have occurred just before or
-	 * just after this set. But since we are just coarsely waiting for
-	 * a frame to complete then that's OK. i.e. if the frame completed
-	 * just before this code executed then we have to wait another full
-	 * frame time but there is no way to avoid such a situation. On the
-	 * other hand if the frame completed just after then we don't need
-	 * to wait long at all. Either way we are guaranteed to return to the
-	 * user immediately after a frame completion which is all that is
-	 * required.
-	 */
-	par->vsync_flag = 0;
-	ret = wait_event_interruptible_timeout(par->vsync_wait,
-					       par->vsync_flag != 0,
-					       par->vsync_timeout);
-	if (ret < 0)
-		return ret;
-	if (ret == 0)
-		return -ETIMEDOUT;
-
-	return 0;
-}
-
-static int fb_ioctl(struct fb_info *info, unsigned int cmd,
-			  unsigned long arg)
-{
-	struct lcd_sync_arg sync_arg;
-
-	switch (cmd) {
-	case FBIOGET_CONTRAST:
-	case FBIOPUT_CONTRAST:
-	case FBIGET_BRIGHTNESS:
-	case FBIPUT_BRIGHTNESS:
-	case FBIGET_COLOR:
-	case FBIPUT_COLOR:
-		return -ENOTTY;
-	case FBIPUT_HSYNC:
-		if (copy_from_user(&sync_arg, (char *)arg,
-				sizeof(struct lcd_sync_arg)))
-			return -EFAULT;
-		lcd_cfg_horizontal_sync(sync_arg.back_porch,
-					sync_arg.pulse_width,
-					sync_arg.front_porch);
-		break;
-	case FBIPUT_VSYNC:
-		if (copy_from_user(&sync_arg, (char *)arg,
-				sizeof(struct lcd_sync_arg)))
-			return -EFAULT;
-		lcd_cfg_vertical_sync(sync_arg.back_porch,
-					sync_arg.pulse_width,
-					sync_arg.front_porch);
-		break;
-	case FBIO_WAITFORVSYNC:
-		return fb_wait_for_vsync(info);
-	default:
-		return -EINVAL;
-	}
-	return 0;
-}
-
-static int cfb_blank(int blank, struct fb_info *info)
-{
-	struct da8xx_fb_par *par = info->par;
-	int ret = 0;
-
-	if (par->blank == blank)
-		return 0;
-
-	par->blank = blank;
-	switch (blank) {
-	case FB_BLANK_UNBLANK:
-		lcd_enable_raster();
-
-		if (par->lcd_supply) {
-			ret = regulator_enable(par->lcd_supply);
-			if (ret)
-				return ret;
-		}
-		break;
-	case FB_BLANK_NORMAL:
-	case FB_BLANK_VSYNC_SUSPEND:
-	case FB_BLANK_HSYNC_SUSPEND:
-	case FB_BLANK_POWERDOWN:
-		if (par->lcd_supply) {
-			ret = regulator_disable(par->lcd_supply);
-			if (ret)
-				return ret;
-		}
-
-		lcd_disable_raster(DA8XX_FRAME_WAIT);
-		break;
-	default:
-		ret = -EINVAL;
-	}
-
-	return ret;
-}
-
-/*
- * Set new x,y offsets in the virtual display for the visible area and switch
- * to the new mode.
- */
-static int da8xx_pan_display(struct fb_var_screeninfo *var,
-			     struct fb_info *fbi)
-{
-	int ret = 0;
-	struct fb_var_screeninfo new_var;
-	struct da8xx_fb_par         *par = fbi->par;
-	struct fb_fix_screeninfo    *fix = &fbi->fix;
-	unsigned int end;
-	unsigned int start;
-	unsigned long irq_flags;
-
-	if (var->xoffset != fbi->var.xoffset ||
-			var->yoffset != fbi->var.yoffset) {
-		memcpy(&new_var, &fbi->var, sizeof(new_var));
-		new_var.xoffset = var->xoffset;
-		new_var.yoffset = var->yoffset;
-		if (fb_check_var(&new_var, fbi))
-			ret = -EINVAL;
-		else {
-			memcpy(&fbi->var, &new_var, sizeof(new_var));
-
-			start	= fix->smem_start +
-				new_var.yoffset * fix->line_length +
-				new_var.xoffset * fbi->var.bits_per_pixel / 8;
-			end	= start + fbi->var.yres * fix->line_length - 1;
-			par->dma_start	= start;
-			par->dma_end	= end;
-			spin_lock_irqsave(&par->lock_for_chan_update,
-					irq_flags);
-			if (par->which_dma_channel_done == 0) {
-				lcdc_write(par->dma_start,
-					   LCD_DMA_FRM_BUF_BASE_ADDR_0_REG);
-				lcdc_write(par->dma_end,
-					   LCD_DMA_FRM_BUF_CEILING_ADDR_0_REG);
-			} else if (par->which_dma_channel_done == 1) {
-				lcdc_write(par->dma_start,
-					   LCD_DMA_FRM_BUF_BASE_ADDR_1_REG);
-				lcdc_write(par->dma_end,
-					   LCD_DMA_FRM_BUF_CEILING_ADDR_1_REG);
-			}
-			spin_unlock_irqrestore(&par->lock_for_chan_update,
-					irq_flags);
-		}
-	}
-
-	return ret;
-}
-
-static int da8xxfb_set_par(struct fb_info *info)
-{
-	struct da8xx_fb_par *par = info->par;
-	int ret;
-	bool raster = da8xx_fb_is_raster_enabled();
-
-	if (raster)
-		lcd_disable_raster(DA8XX_FRAME_WAIT);
-
-	fb_var_to_videomode(&par->mode, &info->var);
-
-	par->cfg.bpp = info->var.bits_per_pixel;
-
-	info->fix.visual = (par->cfg.bpp <= 8) ?
-				FB_VISUAL_PSEUDOCOLOR : FB_VISUAL_TRUECOLOR;
-	info->fix.line_length = (par->mode.xres * par->cfg.bpp) / 8;
-
-	ret = lcd_init(par, &par->cfg, &par->mode);
-	if (ret < 0) {
-		dev_err(par->dev, "lcd init failed\n");
-		return ret;
-	}
-
-	par->dma_start = info->fix.smem_start +
-			 info->var.yoffset * info->fix.line_length +
-			 info->var.xoffset * info->var.bits_per_pixel / 8;
-	par->dma_end   = par->dma_start +
-			 info->var.yres * info->fix.line_length - 1;
-
-	lcdc_write(par->dma_start, LCD_DMA_FRM_BUF_BASE_ADDR_0_REG);
-	lcdc_write(par->dma_end, LCD_DMA_FRM_BUF_CEILING_ADDR_0_REG);
-	lcdc_write(par->dma_start, LCD_DMA_FRM_BUF_BASE_ADDR_1_REG);
-	lcdc_write(par->dma_end, LCD_DMA_FRM_BUF_CEILING_ADDR_1_REG);
-
-	if (raster)
-		lcd_enable_raster();
-
-	return 0;
-}
-
-static const struct fb_ops da8xx_fb_ops = {
-	.owner = THIS_MODULE,
-	FB_DEFAULT_IOMEM_OPS,
-	.fb_check_var = fb_check_var,
-	.fb_set_par = da8xxfb_set_par,
-	.fb_setcolreg = fb_setcolreg,
-	.fb_pan_display = da8xx_pan_display,
-	.fb_ioctl = fb_ioctl,
-	.fb_blank = cfb_blank,
-};
-
-static struct fb_videomode *da8xx_fb_get_videomode(struct platform_device *dev)
-{
-	struct da8xx_lcdc_platform_data *fb_pdata = dev_get_platdata(&dev->dev);
-	struct fb_videomode *lcdc_info;
-	int i;
-
-	for (i = 0, lcdc_info = known_lcd_panels;
-		i < ARRAY_SIZE(known_lcd_panels); i++, lcdc_info++) {
-		if (strcmp(fb_pdata->type, lcdc_info->name) == 0)
-			break;
-	}
-
-	if (i == ARRAY_SIZE(known_lcd_panels)) {
-		dev_err(&dev->dev, "no panel found\n");
-		return NULL;
-	}
-	dev_info(&dev->dev, "found %s panel\n", lcdc_info->name);
-
-	return lcdc_info;
-}
-
-static int fb_probe(struct platform_device *device)
-{
-	struct da8xx_lcdc_platform_data *fb_pdata =
-						dev_get_platdata(&device->dev);
-	struct lcd_ctrl_config *lcd_cfg;
-	struct fb_videomode *lcdc_info;
-	struct fb_info *da8xx_fb_info;
-	struct da8xx_fb_par *par;
-	struct clk *tmp_lcdc_clk;
-	int ret;
-	unsigned long ulcm;
-
-	if (fb_pdata == NULL) {
-		dev_err(&device->dev, "Can not get platform data\n");
-		return -ENOENT;
-	}
-
-	lcdc_info = da8xx_fb_get_videomode(device);
-	if (lcdc_info == NULL)
-		return -ENODEV;
-
-	da8xx_fb_reg_base = devm_platform_ioremap_resource(device, 0);
-	if (IS_ERR(da8xx_fb_reg_base))
-		return PTR_ERR(da8xx_fb_reg_base);
-
-	tmp_lcdc_clk = devm_clk_get(&device->dev, "fck");
-	if (IS_ERR(tmp_lcdc_clk))
-		return dev_err_probe(&device->dev, PTR_ERR(tmp_lcdc_clk),
-				     "Can not get device clock\n");
-
-	pm_runtime_enable(&device->dev);
-	pm_runtime_get_sync(&device->dev);
-
-	/* Determine LCD IP Version */
-	switch (lcdc_read(LCD_PID_REG)) {
-	case 0x4C100102:
-		lcd_revision = LCD_VERSION_1;
-		break;
-	case 0x4F200800:
-	case 0x4F201000:
-		lcd_revision = LCD_VERSION_2;
-		break;
-	default:
-		dev_warn(&device->dev, "Unknown PID Reg value 0x%x, "
-				"defaulting to LCD revision 1\n",
-				lcdc_read(LCD_PID_REG));
-		lcd_revision = LCD_VERSION_1;
-		break;
-	}
-
-	lcd_cfg = (struct lcd_ctrl_config *)fb_pdata->controller_data;
-
-	if (!lcd_cfg) {
-		ret = -EINVAL;
-		goto err_pm_runtime_disable;
-	}
-
-	da8xx_fb_info = framebuffer_alloc(sizeof(struct da8xx_fb_par),
-					&device->dev);
-	if (!da8xx_fb_info) {
-		ret = -ENOMEM;
-		goto err_pm_runtime_disable;
-	}
-
-	par = da8xx_fb_info->par;
-	par->dev = &device->dev;
-	par->lcdc_clk = tmp_lcdc_clk;
-	par->lcdc_clk_rate = clk_get_rate(par->lcdc_clk);
-
-	par->lcd_supply = devm_regulator_get_optional(&device->dev, "lcd");
-	if (IS_ERR(par->lcd_supply)) {
-		if (PTR_ERR(par->lcd_supply) == -EPROBE_DEFER) {
-			ret = -EPROBE_DEFER;
-			goto err_release_fb;
-		}
-
-		par->lcd_supply = NULL;
-	} else {
-		ret = regulator_enable(par->lcd_supply);
-		if (ret)
-			goto err_release_fb;
-	}
-
-	fb_videomode_to_var(&da8xx_fb_var, lcdc_info);
-	par->cfg = *lcd_cfg;
-
-	da8xx_fb_lcd_reset();
-
-	/* allocate frame buffer */
-	par->vram_size = lcdc_info->xres * lcdc_info->yres * lcd_cfg->bpp;
-	ulcm = lcm((lcdc_info->xres * lcd_cfg->bpp)/8, PAGE_SIZE);
-	par->vram_size = roundup(par->vram_size/8, ulcm);
-	par->vram_size = par->vram_size * LCD_NUM_BUFFERS;
-
-	par->vram_virt = dmam_alloc_coherent(par->dev,
-					     par->vram_size,
-					     &par->vram_phys,
-					     GFP_KERNEL | GFP_DMA);
-	if (!par->vram_virt) {
-		dev_err(&device->dev,
-			"GLCD: kmalloc for frame buffer failed\n");
-		ret = -EINVAL;
-		goto err_disable_reg;
-	}
-
-	da8xx_fb_info->screen_base = (char __iomem *) par->vram_virt;
-	da8xx_fb_fix.smem_start    = par->vram_phys;
-	da8xx_fb_fix.smem_len      = par->vram_size;
-	da8xx_fb_fix.line_length   = (lcdc_info->xres * lcd_cfg->bpp) / 8;
-
-	par->dma_start = par->vram_phys;
-	par->dma_end   = par->dma_start + lcdc_info->yres *
-		da8xx_fb_fix.line_length - 1;
-
-	/* allocate palette buffer */
-	par->v_palette_base = dmam_alloc_coherent(par->dev, PALETTE_SIZE,
-						  &par->p_palette_base,
-						  GFP_KERNEL | GFP_DMA);
-	if (!par->v_palette_base) {
-		dev_err(&device->dev,
-			"GLCD: kmalloc for palette buffer failed\n");
-		ret = -EINVAL;
-		goto err_release_fb;
-	}
-
-	par->irq = platform_get_irq(device, 0);
-	if (par->irq < 0) {
-		ret = -ENOENT;
-		goto err_release_fb;
-	}
-
-	da8xx_fb_var.grayscale =
-	    lcd_cfg->panel_shade == MONOCHROME ? 1 : 0;
-	da8xx_fb_var.bits_per_pixel = lcd_cfg->bpp;
-
-	/* Initialize fbinfo */
-	da8xx_fb_info->fix = da8xx_fb_fix;
-	da8xx_fb_info->var = da8xx_fb_var;
-	da8xx_fb_info->fbops = &da8xx_fb_ops;
-	da8xx_fb_info->pseudo_palette = par->pseudo_palette;
-	da8xx_fb_info->fix.visual = (da8xx_fb_info->var.bits_per_pixel <= 8) ?
-				FB_VISUAL_PSEUDOCOLOR : FB_VISUAL_TRUECOLOR;
-
-	ret = fb_alloc_cmap(&da8xx_fb_info->cmap, PALETTE_SIZE, 0);
-	if (ret)
-		goto err_disable_reg;
-	da8xx_fb_info->cmap.len = par->palette_sz;
-
-	/* initialize var_screeninfo */
-	da8xx_fb_var.activate = FB_ACTIVATE_FORCE;
-	fb_set_var(da8xx_fb_info, &da8xx_fb_var);
-
-	platform_set_drvdata(device, da8xx_fb_info);
-
-	/* initialize the vsync wait queue */
-	init_waitqueue_head(&par->vsync_wait);
-	par->vsync_timeout = HZ / 5;
-	par->which_dma_channel_done = -1;
-	spin_lock_init(&par->lock_for_chan_update);
-
-	/* Register the Frame Buffer  */
-	if (register_framebuffer(da8xx_fb_info) < 0) {
-		dev_err(&device->dev,
-			"GLCD: Frame Buffer Registration Failed!\n");
-		ret = -EINVAL;
-		goto err_dealloc_cmap;
-	}
-
-#ifdef CONFIG_CPU_FREQ
-	ret = lcd_da8xx_cpufreq_register(par);
-	if (ret) {
-		dev_err(&device->dev, "failed to register cpufreq\n");
-		goto err_cpu_freq;
-	}
-#endif
-
-	if (lcd_revision == LCD_VERSION_1)
-		lcdc_irq_handler = lcdc_irq_handler_rev01;
-	else {
-		init_waitqueue_head(&frame_done_wq);
-		lcdc_irq_handler = lcdc_irq_handler_rev02;
-	}
-
-	ret = devm_request_irq(&device->dev, par->irq, lcdc_irq_handler, 0,
-			       DRIVER_NAME, par);
-	if (ret)
-		goto irq_freq;
-	return 0;
-
-irq_freq:
-#ifdef CONFIG_CPU_FREQ
-	lcd_da8xx_cpufreq_deregister(par);
-err_cpu_freq:
-#endif
-	unregister_framebuffer(da8xx_fb_info);
-
-err_dealloc_cmap:
-	fb_dealloc_cmap(&da8xx_fb_info->cmap);
-
-err_disable_reg:
-	if (par->lcd_supply)
-		regulator_disable(par->lcd_supply);
-err_release_fb:
-	framebuffer_release(da8xx_fb_info);
-
-err_pm_runtime_disable:
-	pm_runtime_put_sync(&device->dev);
-	pm_runtime_disable(&device->dev);
-
-	return ret;
-}
-
-#ifdef CONFIG_PM_SLEEP
-static struct lcdc_context {
-	u32 clk_enable;
-	u32 ctrl;
-	u32 dma_ctrl;
-	u32 raster_timing_0;
-	u32 raster_timing_1;
-	u32 raster_timing_2;
-	u32 int_enable_set;
-	u32 dma_frm_buf_base_addr_0;
-	u32 dma_frm_buf_ceiling_addr_0;
-	u32 dma_frm_buf_base_addr_1;
-	u32 dma_frm_buf_ceiling_addr_1;
-	u32 raster_ctrl;
-} reg_context;
-
-static void lcd_context_save(void)
-{
-	if (lcd_revision == LCD_VERSION_2) {
-		reg_context.clk_enable = lcdc_read(LCD_CLK_ENABLE_REG);
-		reg_context.int_enable_set = lcdc_read(LCD_INT_ENABLE_SET_REG);
-	}
-
-	reg_context.ctrl = lcdc_read(LCD_CTRL_REG);
-	reg_context.dma_ctrl = lcdc_read(LCD_DMA_CTRL_REG);
-	reg_context.raster_timing_0 = lcdc_read(LCD_RASTER_TIMING_0_REG);
-	reg_context.raster_timing_1 = lcdc_read(LCD_RASTER_TIMING_1_REG);
-	reg_context.raster_timing_2 = lcdc_read(LCD_RASTER_TIMING_2_REG);
-	reg_context.dma_frm_buf_base_addr_0 =
-		lcdc_read(LCD_DMA_FRM_BUF_BASE_ADDR_0_REG);
-	reg_context.dma_frm_buf_ceiling_addr_0 =
-		lcdc_read(LCD_DMA_FRM_BUF_CEILING_ADDR_0_REG);
-	reg_context.dma_frm_buf_base_addr_1 =
-		lcdc_read(LCD_DMA_FRM_BUF_BASE_ADDR_1_REG);
-	reg_context.dma_frm_buf_ceiling_addr_1 =
-		lcdc_read(LCD_DMA_FRM_BUF_CEILING_ADDR_1_REG);
-	reg_context.raster_ctrl = lcdc_read(LCD_RASTER_CTRL_REG);
-	return;
-}
-
-static void lcd_context_restore(void)
-{
-	if (lcd_revision == LCD_VERSION_2) {
-		lcdc_write(reg_context.clk_enable, LCD_CLK_ENABLE_REG);
-		lcdc_write(reg_context.int_enable_set, LCD_INT_ENABLE_SET_REG);
-	}
-
-	lcdc_write(reg_context.ctrl, LCD_CTRL_REG);
-	lcdc_write(reg_context.dma_ctrl, LCD_DMA_CTRL_REG);
-	lcdc_write(reg_context.raster_timing_0, LCD_RASTER_TIMING_0_REG);
-	lcdc_write(reg_context.raster_timing_1, LCD_RASTER_TIMING_1_REG);
-	lcdc_write(reg_context.raster_timing_2, LCD_RASTER_TIMING_2_REG);
-	lcdc_write(reg_context.dma_frm_buf_base_addr_0,
-			LCD_DMA_FRM_BUF_BASE_ADDR_0_REG);
-	lcdc_write(reg_context.dma_frm_buf_ceiling_addr_0,
-			LCD_DMA_FRM_BUF_CEILING_ADDR_0_REG);
-	lcdc_write(reg_context.dma_frm_buf_base_addr_1,
-			LCD_DMA_FRM_BUF_BASE_ADDR_1_REG);
-	lcdc_write(reg_context.dma_frm_buf_ceiling_addr_1,
-			LCD_DMA_FRM_BUF_CEILING_ADDR_1_REG);
-	lcdc_write(reg_context.raster_ctrl, LCD_RASTER_CTRL_REG);
-	return;
-}
-
-static int fb_suspend(struct device *dev)
-{
-	struct fb_info *info = dev_get_drvdata(dev);
-	struct da8xx_fb_par *par = info->par;
-	int ret;
-
-	console_lock();
-	if (par->lcd_supply) {
-		ret = regulator_disable(par->lcd_supply);
-		if (ret)
-			return ret;
-	}
-
-	fb_set_suspend(info, 1);
-	lcd_disable_raster(DA8XX_FRAME_WAIT);
-	lcd_context_save();
-	pm_runtime_put_sync(dev);
-	console_unlock();
-
-	return 0;
-}
-static int fb_resume(struct device *dev)
-{
-	struct fb_info *info = dev_get_drvdata(dev);
-	struct da8xx_fb_par *par = info->par;
-	int ret;
-
-	console_lock();
-	pm_runtime_get_sync(dev);
-	lcd_context_restore();
-	if (par->blank == FB_BLANK_UNBLANK) {
-		lcd_enable_raster();
-
-		if (par->lcd_supply) {
-			ret = regulator_enable(par->lcd_supply);
-			if (ret)
-				return ret;
-		}
-	}
-
-	fb_set_suspend(info, 0);
-	console_unlock();
-
-	return 0;
-}
-#endif
-
-static SIMPLE_DEV_PM_OPS(fb_pm_ops, fb_suspend, fb_resume);
-
-static struct platform_driver da8xx_fb_driver = {
-	.probe = fb_probe,
-	.remove = fb_remove,
-	.driver = {
-		   .name = DRIVER_NAME,
-		   .pm	= &fb_pm_ops,
-		   },
-};
-module_platform_driver(da8xx_fb_driver);
-
-MODULE_DESCRIPTION("Framebuffer driver for TI da8xx/omap-l1xx");
-MODULE_AUTHOR("Texas Instruments");
-MODULE_LICENSE("GPL");
diff --git a/include/video/da8xx-fb.h b/include/video/da8xx-fb.h
deleted file mode 100644
index 1d19ae62b844..000000000000
--- a/include/video/da8xx-fb.h
+++ /dev/null
@@ -1,94 +0,0 @@
-/*
- * Header file for TI DA8XX LCD controller platform data.
- *
- * Copyright (C) 2008-2009 MontaVista Software Inc.
- * Copyright (C) 2008-2009 Texas Instruments Inc
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2. This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
-
-#ifndef DA8XX_FB_H
-#define DA8XX_FB_H
-
-enum panel_shade {
-	MONOCHROME = 0,
-	COLOR_ACTIVE,
-	COLOR_PASSIVE,
-};
-
-enum raster_load_mode {
-	LOAD_DATA = 1,
-	LOAD_PALETTE,
-};
-
-enum da8xx_frame_complete {
-	DA8XX_FRAME_WAIT,
-	DA8XX_FRAME_NOWAIT,
-};
-
-struct da8xx_lcdc_platform_data {
-	const char manu_name[10];
-	void *controller_data;
-	const char type[25];
-};
-
-struct lcd_ctrl_config {
-	enum panel_shade panel_shade;
-
-	/* AC Bias Pin Frequency */
-	int ac_bias;
-
-	/* AC Bias Pin Transitions per Interrupt */
-	int ac_bias_intrpt;
-
-	/* DMA burst size */
-	int dma_burst_sz;
-
-	/* Bits per pixel */
-	int bpp;
-
-	/* FIFO DMA Request Delay */
-	int fdd;
-
-	/* TFT Alternative Signal Mapping (Only for active) */
-	unsigned char tft_alt_mode;
-
-	/* 12 Bit Per Pixel (5-6-5) Mode (Only for passive) */
-	unsigned char stn_565_mode;
-
-	/* Mono 8-bit Mode: 1=D0-D7 or 0=D0-D3 */
-	unsigned char mono_8bit_mode;
-
-	/* Horizontal and Vertical Sync Edge: 0=rising 1=falling */
-	unsigned char sync_edge;
-
-	/* Raster Data Order Select: 1=Most-to-least 0=Least-to-most */
-	unsigned char raster_order;
-
-	/* DMA FIFO threshold */
-	int fifo_th;
-};
-
-struct lcd_sync_arg {
-	int back_porch;
-	int front_porch;
-	int pulse_width;
-};
-
-/* ioctls */
-#define FBIOGET_CONTRAST	_IOR('F', 1, int)
-#define FBIOPUT_CONTRAST	_IOW('F', 2, int)
-#define FBIGET_BRIGHTNESS	_IOR('F', 3, int)
-#define FBIPUT_BRIGHTNESS	_IOW('F', 3, int)
-#define FBIGET_COLOR		_IOR('F', 5, int)
-#define FBIPUT_COLOR		_IOW('F', 6, int)
-#define FBIPUT_HSYNC		_IOW('F', 9, int)
-#define FBIPUT_VSYNC		_IOW('F', 10, int)
-
-/* Proprietary FB_SYNC_ flags */
-#define FB_SYNC_CLK_INVERT 0x40000000
-
-#endif  /* ifndef DA8XX_FB_H */
-